فهرست مطالب

علوم و تکنولوژی پلیمر - سال بیست و چهارم شماره 3 (پیاپی 113، امرداد و شهریور 1390)

دو ماهنامه علوم و تکنولوژی پلیمر
سال بیست و چهارم شماره 3 (پیاپی 113، امرداد و شهریور 1390)

  • تاریخ انتشار: 1390/06/16
  • تعداد عناوین: 7
|
  • محراب مدهوشی، سحر سادات زاده، قنبر ابراهیمی صفحه 171

    به منظور بررسی تقویت اتصالات چوبی، اتصالات دوگانه از چوب های کاج و صنوبر تهیه و با استفاده از اتصال دهنده پیچ و مهره به هم متصل شدند. صفحات پلاستیکی تقویت شده با الیاف شیشه GFRP در دو نوع مختلف تجاری و در ضخامت های 05 / 0 و 1 mmبه عنوان تقویتک ننده و پوشش روی اتصالات با استفاده از رزین اپوکسی، استفاده شد. هم چنین، به منظور حفظ ظاهر اتصال و نمای طبیعی چوب، در نیمی از نمونه ها از لایه نازک چوب نیز روی کامپوزیت استفاده شد. در مجموع 32 نمونه اتصال و 8 نمونه به عنوان شاهد ساخته شد. پس از آماده سازی نمونه ها، آزمون کشش روی آنها اجرا شد. نتایج نشان داد، مقدار بار و تنش اعمال شده با تقویت اتصال افزایش می یابد و در این ارتباط تنها اثر نوع صفحات کامپوزیتی معنی دار است و نوع گونه اثر معنی داری ندارد. هم چنین نتایج نشان داد، تقویت اتصالات موجب تغییر شکل شکست در نمونه های چوبی می شود، به طوری که هیچ یک از نمونه های تقویت شده در محل اتصال با پیچ دچار شکست نشده و تنها در محل پیچ دچار لهیدگی می شود. در نتیجه می توان گفت با تقویت اتصال، ضریب اطمینان سازه افزایش می یابد و ترک های ناگهانی و عمیق در اتصال چوبی ایجاد نمی شود.

    کلیدواژگان: اتصال دوگانه پیچ و مهره چوبی، رزین اپوکسی، کامپوزیت، اتصال تقویت شده، استحکام کششی
  • محمدرضا رستمی درونکلا، محمد علی سمسارزاده* صفحه 181

    در پلیمرشدن رادیکالی انتقال اتم متیل آکریلات با درشت آغازگر پلی وینیل استات در محیط توده و دمای 90 °C تغییرات تبدیل واکنش ([Ln [M]0/[M به طور خطی با زمان افزایش یافت. مقدار ثابت سرعت پلیمرشدن ظاهری Kp app از شیب این تغییرات به دست آمد. این مقادیر برای محاسبه غلظت درشت رادیکال آزاد فعال در محیط واکنش استفاده شد. با افزایش غلظت کلرید مس II)غیرفعال کننده(مقادیر غلظت درشت رادیکال آزاد در محیط واکنش و ثابت سرعت پلیمرشدن ظاهری کاهش یافت.
    با استفاده از معادلات سینتیکی و منحنی تجربی معکوس ثابت سرعت پلیمرشدن ظاهری با غلظت کلرید مس II ، مقادیر ثابت سرعت فعال شدن و نسبت ثابت سرعت غیرفعال شدن به آغاز به ترتیب L/mol.s و 2/576×10-4 و222 به دست آمد. وزن مولکولی متوسط عددی کوپلیمرهای قطعه ای حاصل با روش رنگ نگاری ژل تراوایی GPC با تبدیل واکنش به شکل خطی افزایش یافت که به طور تقریبی مشابه مقادیر نظری بود. افزون بر این، به دلیل رفتار کنترلی زنده در فرایند پلیمرشدن رادیکالی انتقال اتم با درشت آغازگر پلی وینیل استات، با افزایش درصد تبدیل واکنش مقدار توزیع وزن مولکولی کوپلیمرهای قطعه ای کاهش یافت. با افزایش)دو برابر(غلظت درشت آغازگر، کاتالیزور کلرید مس I و کاهش)نصف(غلظت مونومر متیل آکریلات در محیط واکنش، ثابت سرعت پلیمرشدن ظاهری و غلظت درشت رادیکال آزاد در محیط واکنش افزایش یافت. با افزایش غلظت درشت رادیکال در محیط واکنش و درنتیجه وقوع واکنش های اختتام، نسبت ثابت سرعت اختتام به تعادلی Kt/keq نیز برای مونومر متیل آکریلات مقدار 4/313×1020 به دست آمد. هم چنین، با افزایش غلظت درشت رادیکال آزاد و وقوع واکنش های اختتام، مقدار وزن مولکولی متوسط عددی کوپلیمرهای قطعه ای کاهش و توزیع وزن مولکولی آن پهن تر شدند.

    کلیدواژگان: ثابت های سینتیکی، پلیمرشدن رادیکالی انتقال اتم، کوپلیمرهای قطعه ای، وزن مولکولی، درشت آغازگر
  • اکرم شکرزاده، غلامرضا بخشنده، قاسم نادری، محمدجلال الدین ظهوریان مهر* صفحه 195

    در این پژوهش، نمک آلی- فلزی آلومینیم تری آکریلات ALTA با فرمول کلی  (CH2=CH COO)3Al در دو مرحله سنتز و با استفاده از روش های طیف سنجی زیرقرمزDSC و DTA شناسایی شد.سپس، این ترکیب به عنوان پرکننده واکنش پذیر در آمیزه کاری الاستومر اتیلن- پروپیلن- دی ان مونومرEPDM به کار برده شد. آمیزه هایی بر پایهEPDM همراه با دو تقویت کننده ALTA و نانوخاک رس با فرمول بندی کیسان و با تغ ییر در مقدار تقویت کننده تهیه شدند و اثر آنها روی خواص پخت و خواص مکان کیی آمیزه بررسی شد. بررسی نتایج نشان داد، با افزایش مقدار ALTAاستحکام کششی، مدول و ازدیاد طول تا پارگی افزایش بیشتری نسبت به نمونه های حاوی نانوخاک رس یافت. آمیزه های حاوی پرکننده ALTA سختی و سایش بهتری نیز نسبت به
    آمیزه های حاوی نانوخاک رس نشان داد. این افزایش خواص مکانیکی آمیزه های حاوی نمک های فلزی به پلیمرشدن آنها در طول فرایند وولکانش، ارتباط داده شد. ساخت این تقویت کننده ها، گام موثری در راستای دستی ابی به پرکننده های ارزان تر و موثرتر در زمینه تقویت الاستومرها تلقی می شود.

    کلیدواژگان: آلومینیم تری آکریلات، الاستومرEPDM، تقویت کنندگی، سنتز، نانوخاک رس
  • فرشید ضیایی، سید مهرداد جلیلیان* صفحه 205

    امولسیونک ننده ها از اهمیت بسزایی در واکنش های پلیمرشدن امولسیونی برخوردارند. مقدار و نوع امولسیونک ننده روی تمام پارامترهای واکنش از جمله اندازه و توزیع ذرات و وزن مولکولی
    پلیمر موثر است. در این پژوهش، با توجه به اهمیت پلی وینیل کلرید امولسیونی، اثر مخلوط امولسیونک ننده های یونی سدیم لوریل سولفات و غیریونی استیاریل الکل روی پارامترهای مختلف
    واکنش پلیمرشدن امولسیونی وینیل کلرید بررسی شده است. نتایج نشان می دهد، اندازه ذرات پلی وینیل کلرید با افزایش مقدار تر یکب درصد سامانه امولسیونک ننده های یونی و غیریونی کاهش میی ابد. هم چنین، با افزایش مقدار مونومر وینیل کلرید و ثابت بودن سایر اجزا در فرمول بندی، مقدار گرمای آزادشده واکنش در نقطه ژل افزایش می یابد. وزن مولکولی پلیمر با افزایش دمای واکنش کاهش و با ازدیاد تر یکب درصد امولسیونک ننده افزایش پیدا می کند. بررسی ساختاری نمونه پلی وینیل کلرید سنتزی به کمک طیف های 13C NMRو FTIR گویای عدم وجود نقص در ساختار زنجیر پلیمر است. با بهینه کردن شرایط واکنش پلیمرشدن امولسیونی پودر وینیل کلرید سنتز شده دارای اندازه ذرات و توزیع مناسبی است که در پلاستی سول ها به کار می رود

    کلیدواژگان: پلی وینیل کلرید، پلیمرشدن امولسیونی، امولسیونک ننده، وزن مولکولی، اندازه ذرات
  • زهرا شکوری، هدایت الله صادقی قاری* صفحه 215

    در این پژوهش، رفتار چهار پلیمر تجاری)کلتان، ویسکوتک، پاراتون و هایتک(مصرفی در صنعت روغن موتور کشور برای تعیین مناسب ترین پلیمر بهبوددهنده شاخص گرانروی بررسی شد.
    در این راستا رفتار گرانروی، پایداری برشی و هم چنین کارایی این نوع محلول های پلیمری در دمای کم برای لحظه آغاز کار موتور)استارت(با یک دیگر مقایسه شد. رفتار گرانروی محلول های پلیمری دارای غلظت های مختلف 3/ 0، 5/ 0، 7/ 0 و 1% وزنی از نظر پارامترهای شیمی فیزیکی هم چون گرانروی ویژه، گرانروی ذاتی، نسبت گرانروی، قدرت غلیظ کنندگی و شاخص گرانروی با یک دیگر مقایسه شدند. انرژی فعال سازی هریک از محلول های پلیمری تولیدی نیز با استفاده از معادله آرنیوس محاسبه و کارایی پلیمرها در تغییر انرژی فعال سازی و کاهش حساسیت دمایی روغن بررسی شد. در ادامه پایداری برشی این نوع پلیمرهای تجاری در حالت محلول بررسی شد.
    از نتایج آزمون برشی، ارتباط معکوس پایداری برشی پلیمرها در محلول با وزن مولکولی آنها مشخص شد. در نهایت نیز رفتار پلیمرهای مطالعه شده در دمای -15°C به منظور تعیین کارایی بهینه در لحظه آغاز به کار موتور بررسی شد. نتایج نشان داد، پلیمر هایتک با توجه به ساختار مولکولی آن نسبت به سایر پلیمرها کارایی بیشتری دارد. پلیمرهای پاراتون و ویسکوتک نیز رفتار نسبتا مشابهی دارند، اگرچه از نظر گرانروی سنجی ویسکوتک تا اندازه ای برتر از پاراتون و از نظر رفتار برشی پاراتون برتر از ویسکوتک است. پلیمر کلتان نیز تنها قدرت غلیظ کنندگی بیشتری دارد و از نظر کارایی برشی و کارایی در دماهای پایین برای لحظه آغاز به کار موتور نامطلوب است و نمی توان از آن در تولید روغن موتورهای باکیفیت استفاده کرد.

    کلیدواژگان: روغن موتور، کوپلیمر اولفینی، گرانروی، بهبوددهنده شاخص گرانروی، پایداری برشی
  • مهسا رستملو، مهدی نوری، جواد مختاری صفحه 231

    نانو کامپوزیت لیفی شکل از مخلوط پلی اتاکاپرولاکتون و نانوخاک رس کلویزیت 30B 30B به کمک فرایند الکتروریسی تهیه شد. پس از تهیه لایه های نانولیفی از پلی اتاکاپرولاکتون خالص و نانوکامپوزیت پلی اتاکاپرولاکتون نانوخاک رس، اثر غلظت محلول پلیمری و درصد وزنی نانوخاک رس مورد استفاده، بر ساختار نهایی نانوالیاف تشکیل شده بررسی شد. شکل شناسی و قطر نانوالیاف حاصل به وسیله میکروسکوپ نوری و میکروسکوپ الکترونی پویشی مطالعه شد. مشاهده شد، محلول 4% وزنی پلی اتاکاپرولاکتون خالص افشانده شده و طی فرایند الکتروریسی هیچ لیفی در محدوده ولتاژ اعمال شده تولید نشده است. این در حالی است که در غلظت های بیش از 8% امکان الکتروریسی وجود نداشت. هم چنین نتایج نشان داد، وجود پرکننده های معدنی نانوخاک رس، سبب تشکیل الیاف با نقص ساختاری کمتر شده است. در ساختار الیاف الکتروریسی شده پلی کاپرولاکتون خالص دانه هایی وجود دارد. اما، با افزودن نانوخاک رس دانه های کمتر و ساختار لیفی بسیار بهتری در محتوای رسی 1، 3 و 5% وزنی در نانو کامپوزیت ها تشکیل می شود، به طوری که ساختار یکنواخت تری در محتوای رسی 9 و 15 % وزنی مشاهده شد. از طرف دیگر، وجود نانوخاک رس سبب شده است که میانگین قطری نانوالیاف کاهش یابد. گرانروی و رسانایی محلول های تهیه شده اندازه گیری شد. نتایج نشان داد، با افزایش غلظت پلی کاپرولاکتون و مقدار نانوخاک رس ، گرانروی محلول پلی کاپرولاکتون افزایش میی ابد. این در حالی است که وجود نانوخاک رس سبب افزایش رسانایی محلول می شود که کشیدگی محلول را حین ریسندگی افزایش داده و الیاف یکنواخت تر با دانه کمتر را در یک فرایند الکتروریسی نتیجه می دهد. با استفاده از نتایج اندازه گیری گرانروی و رسانایی محلول های ریسندگی، دلیل تغییر در شکل و قطر نانوالیاف تشکیل شده توضیح داده شده است. این نانوالیاف می تواند کاربرد گسترده ای در مهندسی بافت داشته باشند

    کلیدواژگان: پلی اتاکاپرولاکتون، نانوخاک رس، الکتروریسی، نانوالیاف، داربست
  • منصور فخری، هانی یزدی ازناوه، بهزاد شیرکوند هداوند* صفحه 241

    در صنایع پتروشیمی تولیدکننده پلی وینیل کلریدPVCضایعات سنگین که شامل تر یکبات دارای دو یا چند کلر هستند به هنگام خالص سازی اتیلن دیک لرید EDC به وجود می آیند. مقدار زیاد
    ترکیبات کلردار موجود در ضایعات سنگین امکان پلیمرشدن آن را با پلی سولفید قلیایی برای تشکیل پلی سولفید پلیمر می دهد. بنابراین، ضایعات خطرناک برای محیط زیست را می توان بدون هیچ نوع مشکل زیست محیطی به پلی سولفید پلیمر تبدیل کرد. روش هایی برای سنتز پلی سولفید پلیمر از این ضایعات وجود دارد تا بتوان این پلیمر لاستیکی را برای اصلاح قیر مورد استفاده قرار داد. در این پژوهش، اثر پلی سولفید پلیمر  PSP  و پلی سولفید پلیمر تهیه شده از ضایعات سنگین wPSP بر قیر و آسفالت تهیه شده از آنها بررسی و مقایسه شده است. به این منظور، نمونه های 1، 3 و 5% از PSPو wPSP به عنوان اصلاح کننده قیر و آسفالت تهیه و خواص فیزیکی و مکانیکی آنها با کیدیگر مقایسه شده است. نتایج نشان داد، استفاده از این اصلاح کننده جدید باعث کاهش درجه نفوذ  5/ PSP=%39 و 6/ wPSP=%27 (و افزایش دمای نرمی) 8/ PSP=%17 و 5/ wPSP=%15
    در قیر و کاهش شیارشدگی در مخلوط آسفالتی می شود و اثر اندکی بر بهبود استحکام مارشال نمونه های آسفالتی  PSP=%4 و 6/ wPSP=%11  دارد

    کلیدواژگان: قیر اصلاح شده، پلی سولفید پلیمر، استحکام مارشال، خزش دینامیکی، ضایعات
|
  • Mehrab Madhoushi, Sahar Sadatzadeh, Ghanbar Ebrahimi Page 171

    Failure in timber structures occurs mainly in crucial points such as joints areas.Therefore, the idea of using composite sheets in timber joints has been introducedas a method in order to increase the strength and ductility behaviour oftimber joints. This research aims to study the behaviour of bolted joints in poplar andpine woods, which are reinforced by two types of GFRP sheets. A single shear boltedjoint consisted of 3 timber members whose length and width were 30 cm in lengthand 5 cm in width. The thickness of each member was 4 cm for internal part and 2 cmfor external part. The employed steel bolt was 10 cm in length and 1 cm in diameter.In this respect, one layer of GFRP sheet was used to be bonded to timber membersby using epoxy resin and left between the clamps for 24 hours. They were then keptat room temperature for three weeks. Also the effect of adding a wood veneer on thereinforced joints was investigated. The tensile strength of the reinforced and controlsamples (un-reinforced joints) was measured according to ASTM D5652-92 standard.The results show that the reinforced samples have higher tensile strength comparedto that of reinforced joints, although it is not statistically significant. Also, two typesof sheets influence the joint behaviour as the reinforced joints display more ductilitybehaviour.

    Keywords: bolted timber joints, composite, epoxy resin, reinforced connection, tensile strength
  • Mohammad Reza Rostami Daronkola, Mohammad Ali Semsarzadeh* Page 181

    In atom transfer radical polymerization (ATRP) of methyl acrylate (MA) with polyvinyl acetate macroinitiator in bulk at 90°C the plots of Ln [M]0/[M] increased linearly with reaction time. The apparent propagation rate constant (kp app) of the reaction was obtained from the linear curve and used to calculate the free macroradical concentration ([R°]) in polymerization medium. The [R°] and also kp app values decreased with concentration of CuCl2 (deactivator). The slope and extrapolation values of the linear curve of (kp app)-1 versus CuCl2 concentrations and kinetic equations were used to calculate ka and kd/ki constants to be 2.576×10-4 M-1.s-1 and 222. The Mn values of block copolymers obtained by GPC were nearly in agreement with the theoretical values and increased linearly with conversion. Furthermore, PDI decreased with conversion due to the controlled/living behavior of the ATRP with PVAc macroinitiator. The kp app and [R°] values increased with catalyst and macroinitiator concentrations and also decreased with monomer concentration. The polymerization medium undergone termination reactions were attributed to increases of the macroradical concentration. The ratio of kt/Keq = 4.313×1020 was also calculated on the basis of Fischer equation. Furthermore, the Mn values of the block copolymers decreased with free macroradical concentration and the PDI values were also broadened due to termination reaction

    Keywords: kinetic constants, atom transfer radical polymerization, block copolymers, molecular weight, macroinitiato
  • Akram Shokrzadeh, Gholam Reza Bakhshandeh, Mohamad Jalaledin Zohuriaan, Mehr*, Ghasem Naderi Page 195

    The organo-metal salt of aluminum triacrylate (ALTA) with a general formula of (CH2=CHCOO)3Al was synthesized as a reactive fller for elastomers through a two-step synthetic procedure. Fourier transform-infrared spectroscopy (FTIR), DSC and DTA were employed for ALTA analysis and to study its cure characteristics. In this research, two composites based on ethylene propylene diene monomer rubber (EPDM) with two types of reactive fllers of modifed organoclay and ALTA were prepared by a laboratory two-roll mill. The types and different ratios of organoclay and ALTA on curing characteristics, mechanical properties such as tensile properties, hardness, and abrasion resistance were studied. The increase in fller content of both composites led to the incremental increase in tensile strength, modulus, hardness, elongation-at-break and also the incremental increase in abrasion resistance of both composites. The improvement in reinforcing properties of ALTA in comparison with nanoclay is attributed to homopolymerization and graft copolymerization of ALTA at the same time during curing of the EPDM composites by peroxide. Making such additives may be taken as an effective action to achieve more durable and cheaper way to reinforce elastomers.

    Keywords: aluminum triacrylate, EPDM elastomer, reinforcement, synthesis, Nanoclay
  • Seyed Mehrdad Jalilian, Farshid Ziaee Page 205

    A mixture of sodium lauryl sulfate (SLS) as ionic emulsifier and stearyl alcohol as non-ionic emulsifier was employed in a vinyl chloride emulsion polymerization reaction to study the influence of various interactive parameters involved in the reaction system. It was found that the particle size was dependent on the amount and type of emulsifier. The average particle size of polyvinyl chloride was dropped by higher amount of emulsifying agents. At the gel point, more heat was generated by higher amount of vinyl chloride fed into the reaction system. The molecular weight of the polymer was decreased by increases in reaction temperature while, it increased by augmenting the amount of emulsifier. According to the 13C NMR and FTIR spectroscopic data no defect was detected in the chain structure of synthetic polyvinylchloride product. An optimization of polymerizationreaction condition was reached based on ultimate particle size desired for its favorabledistribution in plastisols.

    Keywords: polyvinyl chloride, emulsion polymerization, emulsifier, molecular weight, particle size
  • Zahra Shakouri, Hedayatollah Sadeghi Ghari* Page 215

    Nowdays, production of high quality engine oils is one of the worries of ourcountry’s engine oil industry. In this study, the behavior of four commercialpolymers used in nation motor oil industry in obtaining the best viscosityindex improver was investigated. In this regard, viscometric behavior, shear stabilityand polymers’ performance for engine cranking were compared at low temperature. Inthis respect, viscometry behavior of polymer solutions with different concentrations(0.3, 0.5, 0.7 and 1% by weight) in terms of physical chemistry parameters such asspecific viscosity, intrinsic viscosity, viscosity ratio, thickening power and viscosityindex were compared with each other. The activation energy of each polymer solutionwas calculated using the Arrhenius equation and polymer performance was evaluatedwith respect to activation energy changes and lower oil temperature sensitivity.In continuation, the shear stability of these commercial polymers in solution statewas evaluated. Based on shear stability analysis an inverse relationship was foundbetween polymers’ shear stability and their molecular weights. Finally, the behaviorof the commercial polymers was investigated for determination of optimum performancein engine cranking at-15°C. Based on the obtained data, the most suitablepolymer was identified and indicated as the best to fulfil oil industry’s purposes. Inthis respect the high-tech polymers, based on their molecular structures demonstratethe best performance compared to other polymers. Paratone and Viscotech polymershave relatively shown similar behaviors, although based on viscometric behavior theViscotech is better than Paratone, and based on shear behavior the order of preferenceis reversed. Keltan polymer has just a better thickening power while, it is not consideredsuitable for high quality engine oil at low temperatures of engine cranking for itsweak shear performance and low efficiency.

    Keywords: engine oil, olephin copolymer, viscosity, viscosity index improver, shear stability
  • Mahsa Rostamloo, Mehdi Nouri, Javad Mokhtari Page 231

    Nanofiber mats of poly(ε-caprolactone)/nanoclay nanocomposites werefabricated by electrospinning. The effects of the solution concentrationand the nanoclay content of nanocomposite materials on the finalnanofiber structure were investigated. Morphology and diameter of the nanofiberswere studied using optical and scanning electron microscope. It was observed that thepoly(ε-caprolactone) at concentration of 5% to 8% could be electrospun into thefibrous structure. The results showed that the presence of the nanoclay promoted thecreation of fibrous structures in comparison with the poly(ε-caprolactone) withoutnanoclay. On the other hand, increasing the nanoclay content resulted in a loweraverage fiber diameter. Shear viscosity and conductivity of the solutions were alsoreported. The presence of nanoclay increased conductivity and shear viscosity of thesolutions. Formation of the nanofibers and decrease in their diameters are discussed onthe basis of shear viscosity and conductivity of electrospun solution. This electrospunnanofiber could be used for tissue engineering application.

    Keywords: poly(ε-caprolactone), nanoclay, electrospinning, nanofiber, scaffold
  • Behzad Shirkavand Hadavand, Mansour Fakhri, Hani Yazdi Aznaveh Page 241

    In petrochemical industry, the production of polyvinyl chloride (PVC) is accompaniedby formation of heavy end wastes which consist of a mixture of di andmultichloro compounds as kind of materials which are generated in ethylene dichloride(EDC) purification. A high quantity of chloro compounds found in the heavyend waste allows it to be polymerized with alkaline polysulfides to form polysulfidepolymers. Thus, according to this, the environmentally hazardous heavy ends wastecan now be converted into useful polysulfide polymers without any environmentalproblem. There are some methods for synthesizing a polysulfide polymer (PSP) fromthis waste. PSP with a rubbery property can be used for modification of bitumen. Inthis research the effects of polysulfide polymer (PSP) and the polysulfide polymer preparedby heavy end waste (wPSP) on bitumen and asphalt have been studied. Samplesof 1, 3, 5% of PSP and wPSP as modifiers in bitumen have been prepared and theirphysical and mechanical properties are compared. Using this new modifier causes afall in softening point (PSP=39.5%, wPSP=27.6%) and increase in penetration point(PSP=17.8%, wPSP=15.5%) and in asphalt mixture it causes decreases in rutting buthas a small effect on Marshall strength of asphalt samples (PSP=4%, wPSP=11.6%).

    Keywords: modified bitumen, polysulfide polymer, Marshall strength, dynamic creep, waste