International Journal of Civil Engineering
Volume:15 Issue: 6, 2017

To reveal the deformation mechanism during tunneling in deep soft ground, triaxial unloading confining pressure tests and triaxial unloading creep tests were carried out on sandy mudstone specimens to study the dilatancy and fracturing behavior of soft rock. In the triaxial unloading confining pressure tests, the stress path and different unloading rates were considered to reflect the unloading characteristics of the excavation methods. The unloading rate effects and the rock damage evolution law are studied. The following conclusions are obtained from the results. Firstly, when the unloading rate is smooth, the peak strengths and deviatoric stress–strain curves under the unloading condition are close to those under the conventional loading condition. Secondly, the post-peak brittle characteristics are more apparent with the increasing unloading rates. Thirdly, the soft rock undergoes five deformation and failure regimes of elasticity, pre-peak unloading damage–dilatancy, post-peak brittle drop, linear strain softening and residual perfect plasticity under quasi-static smooth unloading of mechanized excavation which is mainly focused on in this study. Fourthly, the damage evolution law at the pre-peak damage–dilatancy stage follows an exponential function. Fifthly, during the post-peak stages, multistage microfractures are initiated, propagated and finally coalesced forming a shear-fragmentation band with a certain thickness, accompanied by significant volumetric dilatancy. In the triaxial unloading creep tests, multistep unloading of the confining pressure was applied, while the axial pressure was kept constant. The results show that when the deviatoric stress is larger and the experienced creep time is longer, the unloading effect and creep characteristics become more apparent accompanied with obvious lateral dilatancy, eventually leading to significant creep–dilatancy. The progressive failure with time is caused by the damage accumulating with time-dependent crack expansion, which can be called as ‘time-dependent damage and fracturing’. The reasons for the above evolution process are presented, then the deformation mechanism of soft rock is revealed. The soft rock deformation mainly consists of two parts. One part is the pre-peak damage–dilatancy and post-peak fracture–bulking produced at the excavation unloading instant. The other part is creep–dilatancy caused by time-dependent damage and fracturing in a period of time after excavation. The above-mentioned results of damage, dilatancy and fractures evolution process are in good agreement with the in situ monitoring results and previous studies about the surrounding rock convergence, fracturing and EDZ (excavation damaged zone) development.

Rainfall is an important triggering factor influencing the stability of soil slope. Study on some influences of the rainfall on the instability characteristics of unsaturated soil embankment slope has been conducted in this paper. First, based on the effective stress theory of unsaturated soil for single variable, fluid–solid coupling constitutive equations were established. Then, a segment of red clay embankment slope, along a railway from Dazhou to Chengdu, damaged by rainfall, was theoretically, numerically, and experimentally researched by considering both the runoff-underground seepage and the fluid–solid coupling. The failure characteristics of the embankment slope and the numerical simulation results were in excellent agreement. In the end, a sensitivity analysis of the key factors influencing the slope stability subjected to rainfall was performed with emphasis on damage depth as well as infiltration rainfall depth. From the analysis in this paper, it was concluded that the intensity of rainfall, rainfall duration, and long-term strength of soil have most effects on slope stability when subjected to rainfall. These results suggest that the numerical simulation can be used for practical applications.

Pile load tests and numerical analysis of a small-scale model pile in unsaturated clayey soil are presented in this paper. A small-scale model pile was simulated to bear a static axial loading in unsaturated soil using finite element method. All parameters used in the finite element method were obtained in laboratory tests, including the direct shear test, interface direct shear test, and filter paper method. The numerical analysis results were compared with the pile load test results. The results show that the general trend of pile load and pile head settlement relationship obtained by the numerical analysis shows a good consistence with the pile load test results. With increasing water content of the soil, the matric suction, dilatancy angle and shear strength decrease, and consequently the ultimate bearing capacity of pile decreases.

It is vital to control the settlement of ultra-high voltage and long span tower foundation because of the difficult construction and strict deformation control. Based on the thinking of deformation compatibility, the mechanical model of deformation compatibility between pile and soil is established. Relying on the long span tower project Lingzhou–Shaoxing ±800 kV DC transmission lines across the Yangtze River, through checking ultimate bearing capacity of existing pile foundation, it can be obtained that the present design foundation can effectively meet the upper 200–220 t load, but it cannot meet the load requirements about 300 t in the construction. The failures of tower foundation mainly display that piles cut into the soil with penetration type in the early condition. With the load increasing, the shallow soil and infrastructure gradually damage with the whole cap sinking, cushion layer destruction and the surrounding soil uplifting. As a result, tower foundation is unable to withstand the effect of upper overload and the whole tower becomes shear failure. The treatment scheme was proposed that it can improve the cushion thickness and strength combined with grouting consolidation to soil around the piles. Thus, the stability of tower foundation improves significantly and settlement was controlled within the permitted range of below 10 mm, which can meet the structure requirements. The results of numerical simulation based on deformation compatibility between pile and soil coincide well with field measured results.

This paper proposes a modified strain wedge (MSW) model for nonlinear analysis of laterally loaded single piles in clays. The MSW model is used to calculate the soil resistance under increasing pile deflection. The stress–strain behavior of clays in the MSW, which is needed to calculate the soil resistance, is described in terms of both hyperbolic and bilinear stress–strain relationships. The subgrade reaction modulus of soil below the MSW is assumed to equal the conventional subgrade reaction modulus and to remain constant under the lateral loading of the pile. The applicability of the proposed model was verified by eight case histories. The results indicate that (1) the predicted results are consistent with the measurements for all eight full-scale tested piles; (2) the bilinear stress–strain relationship is not recommended for clays because the clays usually have a large ε50 and, thus, they exhibit a linear behavior in the MSW during loading; (3) the predicted pile response is less sensitive to the effective friction angle than to the undrained shear strength; and (4) the proposed MSW model applies to normally consolidated clays and to overconsolidated clays until they reach their peak strength.

In this study, an assessment to excess pore water pressure generated around a single pile and pile group excited by two opposite rotary machines embedded in saturated sandy soil was considered experimentally. A small-scale physical model was manufactured to accomplish the experimental work in the laboratory. The physical model consists of: two small motors supplied with eccentric mass of 0.012 kg and eccentric distance (20 mm) representing the two opposite rotary machines, an aluminum shaft 20 mm in diameter as the pile, and a steel plate with dimensions of (160 × 160 × 20 mm) as a pile cap. The experimental work was achieved taking the following parameters into considerations: pile embedment depth ratio (L/d), spacing between piles (S) and operating frequency of the rotary machines. Twelve tests were conducted in medium dense fine sandy soil with 60 % relative density. In all these tests, the change in excess pore water pressure was measured around the pile at two spots: at the middle of the pile and at its tip. The results revealed that the generation of excess pore water pressure was affected by the following parameters: slenderness ratio of the pile, operating frequency of the machines, and the soil permeability. However, for all cases, it was found that the pore water pressure generated during operation was not greater than 20 % of the initial hydrostatic pressure. Using pile foundation reduced the amplitude of vertical vibration by about (300 %) for all operating frequencies, lengths of piles, pile spacings and number of piles. In addition, the presence of piles reduced the disturbance (fluctuation) in this amplitude by about (400 %). For single pile, and under the same operating frequency, a small decrease in the amplitude of vertical vibration resulted from increasing the length of the pile.

In this study, the shear strength parameters of the Kaolinite clay, as the control material, and the Kaolinite clay reinforced by different percentages of two different types of crumb rubber content have been evaluated. The consolidated drained and unconsolidated undrained triaxial and California bearing ratio tests have been conducted on the control and crumb rubber reinforced soils. Addition of crumb rubber would improve shear strength parameters such as cohesion, friction and dilation angles, stiffness and the ductility of the reinforced soil. 5, 10 and 15 % (by the weight of dry soil) of crumb rubber content were used in this study which were undergone confining stress levels of 100, 200 and 300 kPa and an optimum crumb rubber content is found, which results in the maximum bearing capacity of the soil. Also, due to the non-linearity of the failure mode of reinforced soil and inadequacy of Mohr–Columb envelope for describing the behaviour, a failure mode is proposed for the clay soils reinforced by crumb rubber. This failure criterion is useful for failure envelope of clay-rubber matrix.