Optimization the Spray-Drying Process of Moldavian Balm Plant Extract using Response Surface Methodology and TOPSIS Method
Message:
Article Type:
Research/Original Article (دارای رتبه معتبر)
Abstract:
Introduction

Dracocephalum moldavica L. is an annual plant with blue or white flowers and fragrant leaves which belongs to the family of Lamiaceae with the height of up to 80 cm. This plant is native to Central Asia and is accepted in Central and Eastern Europe. In Iran, it is mainly grown in the province of West Azarbaijan and the Alborz Mountains. The essential oils and extracts derived from the secondary metabolisms which are mainly used in the pharmaceutical industry, dietary, cosmetic, flavoring and also as tea and beverage with sugar or honey. The liquid extract of the herb contains a high percentage of water, which should evaporate to increase shelf-life, easy transport, handling and storage, the ease of standardization and preservation of the product quality. On the other hand, the active compounds of the extracts are affected by temperature, oxygen, light and enzymes. Therefore, because of the uses and benefits of herbal extracts, they need to be dried by a practical and effective method like spray drying. In literature still there are no studies taking into account to the comparisons between RSM and TOPSIS as two important optimization methods. So, as the main objective of the present work, the effects of moisture content, drying performance, total phenol content, total flavonoid content and antioxidant activity have been surveyed. Finally, the optimal point of each process variable was presented by two optimization methods.

Materials and Methods

Aerial parts of Moldavian balm plant were cleaned and drying of plant was carried out under shade and thin layer conditions. The extraction of Moldavian balm was obtained by maceration method using ethanol 50 % (v/v), plant to solvent ratio of 1/10 (w/v). After 48h, the extract was concentrated in a rotary evaporator (Buchi Rotavapor R-205, Switzerland) to obtain a solid concentration of 6%. The used carrier was: Maltodextrin and apple pectin. Different ratios of carrier were prepared, then the ratio was added to distilled water and stirred by a magnetic stirrer. Finally, the solution was mixed with extract. The drying of Moldavian Balm plant extract was performed using a spray-dryer (Büchi B-191, Switzerland) with co-current flow regime. The powders provided by the spray drying were stored in refrigerator until they were needed for the experiment.

Results and Discussion

The results of variance analysis showed that the Box-Behnken design with the second-order model has led to the meaningfulness of the model, insignificant of the Lack of Fit and the appropriate correlation coefficient for each of the responses. A total number of 15 experiments were conducted to investigate the effect of process variables such as inlet air temperature, compressed air flow rate and concentration of carriers on moisture content, drying performance, total phenolic content, total flavonoid content and antioxidant activity of  Moldavian balm powder. Inlet air temperature and compressed air flow rate had the most significant effect on moisture content and drying performance, while Chemical properties of the powder affected by changing the concentration of carriers.
Optimization parameters of the spray drying process was performed using surface response and TOPSIS methods. The optimum predicted conditions in the response surface method and TOPSIS method were obtained at inlet air temperature, compressed air flow rate and concentration of carrier (152.5-150°C), (8.046-7.5 lit min-1) and 20%, respectively.

Conclusions

By comparing two methods, it can be concluded that although they could provide the same optimum points, the RSM is more efficient. Because RSM offers a mathematical model that can be used at any desired point of variables to predict the output quantities as well as describing the process trend, while TOPSIS method is unable to predict the process trend and only provides the ranking of alternatives.

Language:
Persian
Published:
Journal of Agricultural Machinery, Volume:10 Issue: 2, 2020
Pages:
201 to 212
magiran.com/p2101969  
دانلود و مطالعه متن این مقاله با یکی از روشهای زیر امکان پذیر است:
اشتراک شخصی
با عضویت و پرداخت آنلاین حق اشتراک یک‌ساله به مبلغ 990,000ريال می‌توانید 70 عنوان مطلب دانلود کنید!
اشتراک سازمانی
به کتابخانه دانشگاه یا محل کار خود پیشنهاد کنید تا اشتراک سازمانی این پایگاه را برای دسترسی نامحدود همه کاربران به متن مطالب تهیه نمایند!
توجه!
  • حق عضویت دریافتی صرف حمایت از نشریات عضو و نگهداری، تکمیل و توسعه مگیران می‌شود.
  • پرداخت حق اشتراک و دانلود مقالات اجازه بازنشر آن در سایر رسانه‌های چاپی و دیجیتال را به کاربر نمی‌دهد.
دسترسی سراسری کاربران دانشگاه پیام نور!
اعضای هیئت علمی و دانشجویان دانشگاه پیام نور در سراسر کشور، در صورت ثبت نام با ایمیل دانشگاهی، تا پایان فروردین ماه 1403 به مقالات سایت دسترسی خواهند داشت!
In order to view content subscription is required

Personal subscription
Subscribe magiran.com for 50 € euros via PayPal and download 70 articles during a year.
Organization subscription
Please contact us to subscribe your university or library for unlimited access!