فهرست مطالب

سلامت و محیط زیست - سال سوم شماره 4 (پیاپی 10، زمستان 1389)

فصلنامه سلامت و محیط زیست
سال سوم شماره 4 (پیاپی 10، زمستان 1389)

  • تاریخ انتشار: 1389/12/28
  • تعداد عناوین: 12
|
  • کاظم ندافی، رامین نبی زاده، مهسا جهانگیری راد صفحه 359
    زمینه و هدف
    وجود رنگ های آنتروکویینون مثل راکتیوبلو 29 در منابع آب و پساب صنایع نساجی از مشکلات زیست محیطی بسیاری از جوامع است. تاکنون روش های مختلفی برای حذف این رنگ مورد توجه قرار گرفته است که استفاده از جاذب ها از جمله این روش ها به شمار می رود.
    روش بررسی
    آزمایش های جذب سطحی در غلظت اولیه رنگ راکتیوmg/L 30، pH های مختلف و دوزهای مختلف جاذب انجام شد. ایزوترم های جذب رنگ راکتیوبلو 29 بر روی نانوتیوب کربنی تک دیواره براساس آزمون مدل های ایزوترم لانگمیر، فروندلیچ و بت تعیین شدند.
    یافته ها
    حداکثر ظرفیت جذب سطحی رنگ راکتیوبلو 29 بر روی نانوتیوب های کربنی تک دیواره 496 میلی گرم بر گرم بود. آزمایش ها نشان داد که pH بهینه (در میان سه 8 و 5، 3=pH) 5 بود و بعد 3 و 8 =pH به ترتیب در حذف رنگ موثرتر عمل نمودند. هم چنین مشخص گردید که زمان مناسب جهت جذب رنگ راکتیو بلو29 در حالت تعادل 4 ساعت بود.
    نتیجه گیری
    براساس نتایج به دست آمده بهترین مدل ایزوترم جذب بت بود و این موضوع نشان می دهد که جذب سطحی رنگ راکتیوبلو 29 بر روی نانوتیوب های کربنی تک دیواره توسط نیروهای ضعیف واندروالس و به صورت چند لایه اتفاق می افتد.
    کلیدواژگان: رنگ راکتیوبلو 29، نانوتیوب کربنی تک دیواره
  • سعیده همتی برجی، سیمین ناصری، رامین نبی زاده، امیر حسین محوی صفحه 369
    زمینه وهدف
    در صنعت و زندگی روزانه، فنل و ترکیبات فنلی به طور وسیعی استفاده می شود که به دلیل پایداری در محیط، قابلیت انحلال در آب و مشکلات بهداشتی مورد توجه است. بنابراین باید نسبت به حذف آنها و جلوگیری از آلودگی آب های پذیرنده اقدام نمود. هدف اصلی در این مطالعه تجزیه فتوکاتالیستی فنل در یک محیط آبی با استفاده از نانوذرات دی اکسید تیتانیوم (TiO2) غنی شده با آهن (+3Fe) و سنتز شده با روش سل ژل بوده است.
    روش بررسی
    این مطالعه از نوع مطالعات بنیادی کاربردی است. حجم نمونه مورد بررسی 1500 میلی لیتر بود. نتایج حاصل با استفاده از آزمون آماری آنالیز رگرسیون چندگانه بررسی گردید. غلظت های 5، 10، 50 و 100 میلی گرم در لیتر از فنل ابتدا در مراحل جداگانه تحت تاثیر پرتو فرابنفش و دی اکسید تیتانیوم غنی شده با آهن (TiO2-+3Fe) و سپس هر دو به طور همزمان، قرار داده شدند. هم چنین اثر غلظت اولیه فنل، بار Fe 3+-TiO2 و تاثیر pH در میزان تجزیه فتوکاتالیستی فنل مطالعه شد. مقادیر بررسی شده برای فتوکاتالیست برابر با 25/0، 5/0 و 1 گرم در لیتر بود. pH نیز در محدوده اسیدی (3=pH)، خنثی (7=pH) و قلیایی (11=pH) مطالعه شد. به منظور تعیین تاثیر متغیرهای pH، زمان ماند، بار TiO2-+3Fe غلظت اولیه فنل و UV بر کارایی فرایند از آنالیز رگرسیون چندگانه استفاده گردید.
    یافته ها
    نتایج نشان دادند که بالاترین کارایی تجزیه در هر کدام از غلظت های مورد بررسی فنل در pH اسیدی و میزان 5/0 گرم در لیتر 2TiO-+ Fe3در فرایندFe 3+-TiO2 /UV می باشد (4/62 درصد در غلظت 100 میلی گرم در لیتر فنل) هم چنین با افزایش غلظت اولیه فنل میزان تجزیه فتوکاتالیستی کاهش یافت. استفاده از پرتو فرابنفش به تنهایی، در مقایسه با فرایند Fe 3+-TiO2 /UV کارایی کم تری در تجزیه فنل به ویژه در غلظت های بالاتر آن داشت (6/38 درصد در غلظت 100 میلی گرم در لیتر فنل). هم چنین میزان جذب سطحی فنل بر کاتالیستTiO2-+3Fe در تاریکی بسیار ناچیز بود.
    نتیجه گیری
    نتیجه این بررسی نشان داد که نانو فتوکاتالیست 2TiO-+3 Feنقش موثری در تجزیه فتوکاتالیستی فنل به ویژه در غلظت های بالاتر آن در فرایند Fe 3+-TiO2 /UV دارد.
  • محمد منشوری، احمدرضا یزدانبخش، مهدیه سردار، امیر شیخ محمدی صفحه 381
    زمینه و هدف
    سمیت زیاد، سرطان زایی و جهش زایی از جمله مشکلاتی است که مواد رنگزای راکتیو برای پستان داران و موجودات آبزی ایجاد می کنند. از جمله روش های متداول برای حذف مواد رنگزا می توان به روش های فیزیکی و شیمیایی نظیر جذب، انعقاد، ته نشینی، فیلتراسیون و... اشاره نمود. به دلیل محدودیت ها و مشکلات این روش ها، تصفیه زیستی که روشی اقتصادی و موثر برای پالایش و آلودگی زدایی از فاضلاب های آلوده به مواد رنگزاست ترجیح داده می شود، در این تحقیق توانایی حذف ماده رنگزایRB-B از محیط آبی توسط مخلوط باکتریایی در شرایط آنوکسیک مورد بررسی قرار گرفت.
    روش بررسی
    مخلوط باکتریایی از لجن فعال صنعت نساجی در محیط کشت لوریا براث حاوی ماده رنگزای RB-B به عنوان منبع کربن، غنی سازی شد. سپس با استفاده از مخلوط باکتریایی حاصل، تجزیه زیستی در فاضلاب سنتتیک در چهار راکتور ناپیوسته مورد بررسی قرار گرفت. میزان کاهش رنگ نمونه ها توسط اسپکتروفتومتر UV-vis و هم چنین میزان رشد جمعیت میکروبی بر اساس آزمایش MPN تعیین شد.
    یافته ها
    راندمان رنگزدایی توسط مخلوط باکتریایی در غلظت های 50 و 250 میلیگرم برلیتر در زمان های به ترتیب 72 و 144 ساعت (3 و 6 روز) بیش از 99 درصد و برای غلظت 500 میلی گرم برلیتر 1/98 درصد در طول زمان 240 ساعت (10 روز) به دست آمد. نرخ کاهش ماده رنگزا برای غلظت های 50، 250 و500 میلی گرم برلیتر پس از حذف کامل به ترتیب به حدود 69/0، 74/1 و 00/2 میلی گرم برلیتر درساعت رسید.
    نتیجه گیری
    نتایج نشان داد، باکتری های آلکالی ژنز دنیتروفیکانس و آلکالی ژنز زایلواکسیدانس جدا شده از لجن فعال توانایی خوبی در حذف ماده رنگزای RB-B داشته و میزان حذف توسط این باکتری ها به غلظت اولیه رنگ بستگی دارد و با افزایش غلظت اولیه نرخ حذف ماده رنگزا افزایش می یابد.
    کلیدواژگان: پاراکلروفنل، پراکسیدهیدروژن، پودر آهن، Ph، فاضلاب
  • پگاه بهمنی، روشنک رضایی کلانتری، میترا غلامی، احمد احمد جنیدی جعفری، زهره زهره جوادی صفحه 389
    زمینه و هدف
    سمیت زیاد، سرطان زایی و جهش زایی از جمله مشکلاتی است که مواد رنگزای راکتیو برای پستان داران و موجودات آبزی ایجاد می کنند. از جمله روش های متداول برای حذف مواد رنگزا می توان به روش های فیزیکی و شیمیایی نظیر جذب، انعقاد، ته نشینی، فیلتراسیون و... اشاره نمود. به دلیل محدودیت ها و مشکلات این روش ها، تصفیه زیستی که روشی اقتصادی و موثر برای پالایش و آلودگی زدایی از فاضلاب های آلوده به مواد رنگزاست ترجیح داده می شود، در این تحقیق توانایی حذف ماده رنگزایRB-B از محیط آبی توسط مخلوط باکتریایی در شرایط آنوکسیک مورد بررسی قرار گرفت.
    روش بررسی
    مخلوط باکتریایی از لجن فعال صنعت نساجی در محیط کشت لوریا براث حاوی ماده رنگزای RB-B به عنوان منبع کربن، غنی سازی شد. سپس با استفاده از مخلوط باکتریایی حاصل، تجزیه زیستی در فاضلاب سنتتیک در چهار راکتور ناپیوسته مورد بررسی قرار گرفت. میزان کاهش رنگ نمونه ها توسط اسپکتروفتومتر UV-vis و هم چنین میزان رشد جمعیت میکروبی بر اساس آزمایش MPN تعیین شد.
    یافته ها
    راندمان رنگزدایی توسط مخلوط باکتریایی در غلظت های 50 و 250 میلیگرم برلیتر در زمان های به ترتیب 72 و 144 ساعت (3 و 6 روز) بیش از 99 درصد و برای غلظت 500 میلی گرم برلیتر 1/98 درصد در طول زمان 240 ساعت (10 روز) به دست آمد. نرخ کاهش ماده رنگزا برای غلظت های 50، 250 و500 میلی گرم برلیتر پس از حذف کامل به ترتیب به حدود 69/0، 74/1 و 00/2 میلی گرم برلیتر درساعت رسید.
    نتیجه گیری
    نتایج نشان داد، باکتری های آلکالی ژنز دنیتروفیکانس و آلکالی ژنز زایلواکسیدانس جدا شده از لجن فعال توانایی خوبی در حذف ماده رنگزای RB-B داشته و میزان حذف توسط این باکتری ها به غلظت اولیه رنگ بستگی دارد و با افزایش غلظت اولیه نرخ حذف ماده رنگزا افزایش می یابد
    کلیدواژگان: صنایع نساجی، ماده رنگزای RB، B، مخلوط باکتریایی، تجزیه بیولوژیکی
  • محمدرضا سمرقندی، محمد نوری سپهر، منصور ضرابی، مهدی نوروزی، الهام شاهرخی، فرشته امرایی صفحه 399
    زمینه و هدف
    تصفیه فاضلاب های رنگی با استفاده از روش های موثر یکی از مهم ترین چالش های پیش روی مهندسان محیط زیست است. فرایند جذب سطحی یکی از موثرترین روش های حذف آلاینده های آلی از فاضلاب هاست. هدف اصلی این پژوهش بررسی کارایی سنگ آتشفشانی پامیس در حذف رنگ اسید بلاک 1 از محیط های آبی بوده است.
    روش بررسی
    در این پژوهش از پامیس برای حذف یک نوع رنگ اسیدی از محلول های سنتیتیک استفاده شده است. برای افزایش تخلخل جاذب مورد استفاده از اسید کلریدریک یک نرمال استفاده گردیده است. تاثیر غلظت اولیه رنگ، pH و زمان تماس بروی کارایی حذف رنگ مورد بررسی قرار گرفت.
    یافته ها
    نتایج نشان داد که کارایی حذف رنگ با افزایش زمان تماس و غلظت اولیه رنگ افزایش و با افزایش pH کاهش می یابد. از مدل های ایزوترمی فروندلیچ و لانگمیر برای محاسبه ثابت های تعادل استفاده گردید. نتایج نشان داد که حذف رنگ اسید بلاک 1 از مدل ایزوترمی لانگمیر (98/0
    نتیجه گیری
    نتایج حاصل از پژوهش حاضر مشخص کرد که پامیس کارایی بسیار بالای در حذف رنگ اسید بلاک 1 از خود نشان می دهد.
    کلیدواژگان: جذب سطحی، رنگ های آزو، سیستم ناپیوسته، نفوذ بین ذره ای، پامیس
  • محمدهادی دهقانی، سیمین ناصری، منصور قادرپوری، امیرحسین محوی، رامین نبی زاده نودهی صفحه 411
    زمینه و هدف
    سورفکتانت ها یکی از بزرگ ترین زنوبیوتیک های موجود در فاضلاب های شهری و صنعتی هستند. طی یک دهه گذشته مقادیر زیادی از سورفکتانت ها به علت افزایش استفاده از دترجنت های مصنوعی در مصارف صنعتی و خانگی وارد محیط زیست شده است. در این تحقیق پتانسیل حذف آلکیل بنزن سولفونات خطی از محلول سنتتیک با فرایند اکسیداسیون پیشرفته UV/H2O2 مورد بررسی قرار گرفته است.
    روش بررسی
    در این مطالعه برای تعیین مقدار دترجنت های آنیونی از روش متیلن بلو و برای اندازه گیری میزان جذب از دستگاه فتومتر در طول موج 652 نانومتر استفاده گردید. برای بررسی کارایی فرایند از متغیرهای غلظت پراکسید هیدروژن، غلظت اولیه دترجنت، pH و مدت زمان تابش استفاده گردید و پتانسیل استفاده از فرایند برای تجزیه آلکیل بنزن سولفونات خطی با آزمون رگرسیون خطی چندگانه آنالیز گردید.
    یافته ها
    راندمان تابش فرابنفش به تنهایی در حذف دترجنت در مدت زمان 20 دقیقه و در8=pH برای غلظت های دترجنت 50 میلی گرم در لیتر برابر 88/38 درصد می باشد. نتایج این آزمایش ها نشان داد که پراکسید هیدروژن در مدت زمان های 10، 20 و 30 دقیقه هیچ تاثیری بر روی محلول دترجنت تهیه شده نداشته است. کارایی فرایند ترکیبی در مدت زمان های 10، 20 و 30 دقیقه به ترتیب برابر 2/86، 90 و 5/96 درصد بوده است.
    نتیجه گیری
    نتایج مطالعه نشان داد که کارایی تابش فرابنفش و پراکسید هیدروژن به تنهایی روش موثری برای حذف دترجنت آنیونی نیست ولی فرایند ترکیبی UV/H2O2 روش مناسبی در حذف دترجنت هاست.
    کلیدواژگان: اکسیداسیون پیشرفته، دترجنت های آنیونی، فرایند UV، H O، فاضلاب صنعتی
  • رضا فولادی فرد، علی اصغر ابراهیمی صفحه 419
    زمینه و هدف
    نیکل (II)و کادمیوم (II) از آلاینده های مهم در محیط زیست محسوب می شوند. روش جذب زیستی به علت کاهش دادن مشکلات لجن، صرفه اقتصادی، کارایی بالا و سازگاری با محیط زیست می تواند روشی موثر برای حذف و بازیابی یون های فلزی از محیط های آبی باشد.
    روش بررسی
    پودر لجن فعال دفعی فاضلاب شهری در راکتور ناپیوسته با محلول های 025/0 و 75/0 میلی مولار فلزات نیکل(II) و کادمیوم (II) در pH و میزان اختلاط های تعیین شده و دمای 26-24 درجه سلسیوس تماس داده شد. نمونه ها بعد از دو ساعت (و یا زمان های متوالی در مطالعه سینتیک) از سیستم گرفته شده و توسط فیلتر صاف گردیدند و توسط دستگاه جذب اتمی جهت بررسی میزان جذب مورد سنجش قرار گرفتند.
    یافته ها
    مطالعات سینتیک نشان دادند که زمان تعادل جذب هر دو فلز در حدود دو ساعت بوده اما پروفیل جذب کادمیوم (II) منظم تر بوده است. جذب هر دو فلز از مدل لانگمیر تبعیت کرده و میزان حداکثر ظرفیت جذب(qmax) نیکل (II) و کادمیوم (II) توسطپودر لجن فعال دفعی به ترتیب 195/0 و 37/0 میلی مول بر گرم برآورد شد. افزایش pH تا چهار باعث افزایش جذب هردو فلز شد. برای کادمیوم(II) در هردو غلظت 25/0 و 75/0 میلی مولار درpH دو جذبی صورت نگرفته اما برای غلظت 25/0 میلی مولار نیکل جذب وجود داشت. میزان اپتیمم اختلاط برای هر دو فلز حدود 200 دور بر دقیقه بوده که تاثیر میزان اختلاط در غلظت های بالاتر فلزات مشهودتر بوده است.
    نتیجه گیری
    هم چون دیگر جاذب ها زیستی، پودر لجن فعال دفعی برای فلز کادمیوم (II) نسبت به نیکل (II) ظرفیت جذب بیش تری داشت و فلز کادمیوم(II) در مدل سازی و نمودارهای بررسی شرایط جذب، تطابق بیش تری از خود نشان داده است.
    کلیدواژگان: جذب زیستی، محیط آبی، پودر لجن فعال دفعی، نیکل (II)، کادمیوم (II)
  • ولی علی پور، لیلا رضایی صفحه 431
    زمینه و هدف
    فیلترهای دو بستری دارای بستری دو لایه ای از جنس ماسه و آنتراسیت هستند. مزیت فیلترهای دو بستری کاربرد طولانی تر فیلتر و افزایش میزان صافسازی است. هدف از این مطالعه، دستیابی به یک مدل اجرایی جهت ارتقای صافی های تک بستری تصفیه خانه های آب بود.
    روش بررسی
    دراین مطالعه مقطعی، دو پایلوت، صافی تک بستری و دو بستری ساخته و از آنها نمونه برداری شد. مدت نمونه برداری 5 ماه و تعداد نمونه ها از ورودی و خروجی هر پایلوت، 40 نمونه بود. بر روی نمونه ها سنجش کدورت و کل کربن آلی و بر روی پایلوت سنجش افت فشار انجام گرفت.
    یافته ها
    میانگین حذف کدورت در پایلوت یک لایه و دو لایه به ترتیب 63 و65 درصد بود. میانگین حذف کل کربن آلی در پایلوت دو بستری و تک بستری به ترتیب ترتیب 66 و 40 درصد و افت فشار در این دو پایلوت به ترتیب دو بستری و یک بستری، 68/0 و 15/1 متر بود.
    نتیجه گیری
    در دو پایلوت، اختلاف در میانگین حذف کدورت معنی دار نبود ولی در میزان حذف کل کربن آلی معنی دار بود. میانگین افت فشار در پایلوت تک بستری بیشتر از نوع دو بستری بود. نسبت پارامترUFRV در صافی دو بستری نسبت به یک بستری معادل (30/51) یعنی 70/1 است و این بدان معنی است که با تغییر بستر از یک بستری به دو بستری، ظرفیت کمی صاف سازی 70 درصد بهبود می یابد.
    کلیدواژگان: صافی، بستر، آنتراسیت، افت فشار، UFRV، بندرعباس
  • افشین ملکی، اکبر اسلامی صفحه 439
    زمینه و هدف
    آلودگی آب به آرسنیک اخیرا به عنوان مشکلی بزرگ مورد توجه قرار گرفته و معضلات اپیدمیولوژیک آن برای سلامت انسان ها گزارش شده است. بنابراین هدف از انجام این مطالعه جذب آرسنیک توسط کاه گندم اصلاح شده توسط بیکربنات سدیم از محیط آبی است.
    روش بررسی
    فرایند جذب به صورت منقطع و در شرایط آزمایشگاهی با تاکید بر اثرات پارامترهای مختلفی چون pH، زمان تماس، غلظت آرسنیک و مقدار جاذب بر راندمان جذب مورد بررسی قرار گرفت. به منظور تفهیم بهتر فرایند جذب، سینتیک جذب و ایزوترم های تعادلی تعیین شد.
    یافته ها
    نتایج نشان داد که جذب متاثر از فاکتورهایی چون غلظت اولیه آرسنیک، مقدار جاذب و pH محیط آبی است. حداکثر جذب آرسنیک در pH حدود 7 حاصل شد. همان طور که انتظار می رفت مقدار آرسنیک جذب شده با افزایش مقدار آرسنیک، افزایش یافت. در بین سه مدل ایزوترم مورد بررسی شامل مدل لانگمیر، فروندلیچ و دوبینین رادشکویچ، دو مدل لانگمیر و فروندلیچ جذب آرسنیک بر روی کاه گندم اصلاح شده را به خوبی توصیف نمودند. هم چنین مشخص شد که جذب از سینتیک درجه دوم کاذب پیروی می کند. متوسط انرژی آزاد جذب (8/15 کیلو ژول بر مول) نشان دهنده مکانیسم جذب شیمیایی آرسنیک بر روی جاذب است. مطالعه واجذب آرسنیک نیز نشان داد که اتصال قوی بین یون های آرسنیک با سایت های موجود بر روی جاذب وجود دارد که منجر به واجذب اندکی شده است.
    نتیجه گیری
    بر مبنای نتایج حاصل از این مطالعه می توان اظهار نمود که روش جذب سطحی با استفاده از کاه گندم اصلاح شده یک روش کارامد و قابل اطمینان برای حذف آرسنیک از محلول های آبی است.
    کلیدواژگان: جذب، کاه گندم، ایزوترم جذب، آرسنیک
  • مجید مسچی نظامی، حسین گنجی دوست، نادر مختارانی، بیتا آیتی صفحه 451
    زمینه و هدف
    با توجه به این که لجن تولید شده در تصفیه خانه ها یکی از مشکلات عمده در زمینه محیط زیست است، کاهش حجم لجن تولیدی در اثر تشکیل پلیمر از اهداف این تحقیق بود.
    روش بررسی
    از یک راکتور SBR (هوازی بی هوازی) به حجم 10 لیتر جهت سازگاری میکروارگانیسم ها و از یک راکتور تولید پلیمر (PPR) به حجم 5/1 لیتر جهت تولید پلیمر استفاده شد. خوراک این سیستم از فاضلاب شهری به همراه غلظت های مختلف اسیدهای چرب فرار (استات و پروپیونات سدیم) تامین گشت و زمان های ماند سلولی 5، 7 و 10 روز در میزان تولید پلیمر بررسی شد.
    یافته ها
    زمان ماند سلولی 5 روز با اختلاف کمی از دو زمان دیگر پلیمر بیشتری تولید کرد و استات با غلظت mg/L 3000 در راکتور تولید پلیمر بیش ترین راندمان تولید PHA یعنی 25 درصد وزن خشک سلول را نتیجه داد.
    نتیجه گیری
    تولید پلیمر از لجن فعال باعث کاهش حجم لجن شد که بیش ترین میزان کاهش حجم لجن با اعمال شرایط بهینه حاصل در روند تحقیق 19 درصد بود.
    کلیدواژگان: پلی هیدروکسی آلکانوات ها، لجن فعال، فاضلاب شهری، کاهش حجم لجن، راندمان تولید PHA
  • علیرضا رحمانی، مهری سلیمانی امین آباد، قربان عسگری، فاطمه برجسته عسکری صفحه 461
    زمینه و هدف
    بالا بودن نیترات درمنابع آبی باعث مشکلات بهداشتی و زیست محیطی متعددی می گردد. در این تحقیق از منیزیم تثبیت شده بر روی سنگ آتشفشانی پامیس و فلز منیزیم (با ظرفیت صفر) برای حذف نیترات استفاده گردید.
    روش بررسی
    گرانول پامیس با کلرید منیزیم اصلاح گردید و حذف نیترات از محلول های آبی در یک سیستم منقطع مورد بررسی قرار گرفت. پارامترهایpH، غلظت اولیه و مقدار دوز جاذب بررسی و از مدل های ایزوترمی لانگمیر و فروندلیچ در جذب آنیون توسط پامیس استفاده شد. همچنین از فلز منیزیم نیز جهت حذف نیترات استفاده شد. در این سیستم نیز پارامترهای pH، غلظت اولیه و دوز منیزیم مورد بررسی قرارگرفتند.
    یافته ها
    راندمان حذف نیترات با استفاده از فلز منیزیم در pH های اولیه 3، 5 و 7 با کنترل pH، به ترتیب برابر با 70%، 40% و 30% تعیین شد که این نتایج نسبت به شرایط بدون کنترل pH بیش تر است. با افزایش غلظت اولیه نیترات در مقدار شرایط نسبت مولی ثابت منیزیم به نیترات، راندمان حذف نیترات افزایش یافت. با استفاده از پامیس اصلاح شده مقدار راندمان حذف نیترات در pH های اولیه 3، 5/6 و 10 با کنترل pH به ترتیب برابر با 49%، 29% و 16% تعیین گردید. با افزایش غلظت اولیه نیترات، راندمان حذف نیترات با پامیس اصلاح شده افزایش یافت. مقادیر ضریب تعیین در جذب نیترات با استفاده از پامیس اصلاح شده برای مدل های ایزوترمی لانگمیر و فروندلیچ به ترتیب برابر با 944/0 و 810/0 تعیین شد. جذب نیترات از مدل لانگمیر پیروی نمود و مقدار نیترات جذب شده به ازای واحد جرم پامیس اصلاح شده mg/g 68/0 تعیین گردید.
    نتیجه گیری
    پامیس اصلاح شده با کلرید منیزیم راندمان کم تری نسبت به فلز منیزیم در حذف نیترات دارد و استفاده از آن نسبت به فلز منیزیم، کم تر تحت تاثیر pH می باشد. در استفاده از فلز منیزیم، توجه به pH محلول به منظور رسیدن به نقطه حذف بهینه نیترات ضروری است.
    کلیدواژگان: پامیس اصلاح شده، منیزیم صفر ظرفیتی، نیترات، جذب سطحی
  • ایرج شاکری نیا صفحه 475
    زمینه و هدف
    تحقیق حاضربا هدف بررسی رابطه ادراک صدا، سرسختی روان شناختی و سلامت روان با کیفیت زندگی زنان خانه دار شهر رشت انجام شده است.
    روش بررسی
    پس ازاندازه گیری میزان صدا درخیابان های مختلف، 50 زن خانه دار ساکن دردوخیابان پرسرصدای شهر رشت به صورت تصادفی انتخاب شده، پرسش نامه های تحقیق را تکمیل کردند. داده های به دست آمده با ضریب همبستگی پیرسون و تحلیل رگرسیون تجزیه و تحلیل شدند.
    یافته ها
    نتایج نشان داد که میزان ادراک صدا، سرسختی روان شناختی و سلامت روانی با کیفیت زندگی رابطه معنی دار دارد. مقدار آمارF به دست آمده از تحلیل رگرسیون در سطح 01/0 >P معنی داربوده، 91% واریانس میان میزان صدا با سرسختی روان شناختی، سلامت روان با کیفیت زندگی مشترک است. از بین میزان ادراک صدا، سرسختی روان شناختی و سلامت روانی، ادراک صدا و سلامت روانی توانسته است واریانس مربوط به کیفیت زندگی زنان خانه دار را تبیین کند به این معنی که افزوده شدن مقدار واریانس سرسختی روان شناختی به معادله، موجب افزایش معنی داری نشده است.
    نتیجه گیری
    باتوجه به اثرگذاری مولفه های محیطی (نظیرصدا) و روان شناختی (نظیرسلامت روانی) برکیفیت زندگی، توسعه و پیشرفت جوامع وکاهش هزینه های خدمات اجتماعی، پیشنهاد این تحقیق این است که همه نهادهای مسئول و دست اندرکارسلامتی جامعه، برنامه های خود را جهت ارتقای کیفیت زندگی آحاد اجتماعی تنظیم کنند و این کار را از طریق کاهش آثارخطرناک و زیان بار متغیرهای محیطی و تقویت مولفه های روان شناختی انجام دهند.
    کلیدواژگان: آلودگی صوتی، کیفیت زندگی، سرسختی روان شناختی، سلامت روان
|
  • K. Naddafi, R. Nabizadeh Nodehi, M. Jahangiri Rad Page 359
    Backgrounds and
    Objectives
    Anthraquinone dyes such as reactive blue29 in water resources and industrial wastewater effluents are one of the most environmental setbacks in many countries. Various methods have been considered to remove these dyes One of which is adsorption.
    Materials And Methods
    All adsorption experiments were conducted in different pHs and various concentrations of adsorbents. The initial concentration of reactive blue 29 chosen in this study was 30mg/L.Adsorption isotherms were determined and correlated with Longmuir, Freundlich and BET models.
    Results
    The maximum adsorption capacity of reactive blue 29 onto single wall carbon nanotubes was 496mg/g.Results showed that the best pH for adsorption was 5 followed by pH3 and 8. Kinetic study showed that the equilibrium time for adsorption of RB 29 to SWCNT is 4 hr.
    Conclusion
    According to the results obtained BET isotherm fitted well the experiment. It shows the adsorption of reactive blue 29 onto single wall carbon nanotubes is multilayers and the mechanism of SWCNTs adsorption toward RB29 is based on weak van der waals forces.
  • S. Hemmati Borji, S. Nasseri, R. Nabizadeh Nodehi, A.H. Mahvi, A.H. Javadi Page 369
    Backgrounds and
    Objectives
    Phenol and phenolic compounds are widely used in industry and daily liFe, and are of high interest due to stability in the environment, dissolution ability in water and health problems. In this regard, phenol removal from water is of high importance. The purpose of this study was to investigate the efficiency of photodegradation process for removal of phenol from aqueous system by use of Fe-doped TiO2 nanoparticles prepared by sol-gel method.
    Materials And Methods
    Phenol concentrations of 5, 10, 50 and 100 mg/L were prepared and exposed to UV and Fe-doped TiO2, separately and simultaneously. Also the effect of initial phenol concentration, Fe-doped TiO2 loading and pH were studied. Various doses of photocatalist investigated for Fe- doped TiO2 were 0.25, 0.5 and 1 g/L. pH was studied at three ranges, acidic (pH=3), neutral (pH=7) and alkaline (pH=11).
    Results
    Maximum degradation was obtained at acidic pH, 0.5 g/L of Fe-doped TiO2 for all of phenol concentrations. With increasing initial concentration of phenol, photocatalytic degradation decreased. In comparison with Fe-doped TiO2/UV process, efficiency of UV radiation alone was low in phenol degradation (% 64.5 at 100 mg/l of phenol concentration). Also the amount of phenol adsorbed on the Fe-doped TiO2 was negligible at dark conditions.
    Conclusion
    Results of this study showed that Fe(III)- doped TiO2 nanoparticles had an important effect on photocatalytic degradation of high initial phenol concentration when Fe(III)-doped TiO2/ UV process applied.
  • M. Manshouri, A.R. Yazdanbakhsh, M. Sardar, A. Sheykh Mohammadi Page 381
    Backgrounds and
    Objectives
    Chlorophenol compounds are used frequently in industries including: petrochemical، producing pesticide and herbicides، producing antimicrobial agents، pharmaceutical and refineries. These compounds can enter the environment through the wastewater industries. This investigation has studied the application of Fenton-like process (Fe0/H2O2) in removal of Parachlorophenol.
    Materials And Methods
    A laboratory scale study was done on a synthetic wastewater containing Para-chlorophenol. Concentration of 10 mg/L of Para-chlorophenol was prepared then optimal values of affecting parameters such as pH، hydrogen peroxide، and iron powder and detention time in the process for Para-chlorophenol removal were determined.
    Results
    The optimum pH، molar ratio of hydrogen peroxide on Para-chlorophenol، hydrogen peroxide on iron powder and time were 4، 18. 8، 0. 4 and 5 minutes respectively. The results showed that removal efficiency in optimal conditions for concentrations of 10، 50 and 100 mg/L are 93. 9، 94. 4 and 94. 3 respectively. The study showed the rate of mineralization of Para-chlorophenol is not completed.
    Conclusion
    According to the results of this study and high resistance in degradation by biological processes، Fenton like process can be used for conversion Para-chlorophenol resistant compound to other compounds with ability of higher biological degradation and lower toxicity.
  • P. Bahmani, R. Rezaei Kalantary, M. Gholami, A. Jonidi Jafari, Z. Javadi Page 389
    Backgrounds and
    Objectives
    Reactive dyestuff has potential of toxicity, carcinogenesis and mutagenesis for mammals and aquatic organisms. The current physical and chemical methods such as adsorption, coagulation, precipitation, filtration and. .. can been used for removing of dyestuff. Biological treatment which is effective and economic for decontamination of dyestuff wastewaters was preferred because of limitation and difficulty of physicochemical methods. In order to investigate the trend of pollution reduction of color compounds, ability of Remazol Black-B dyestuff removal from aqueous medium by bacterial consortium under anoxic conditions was studied.
    Materials And Methods
    The mix culture of bacteria from textile industries activated sludge was enriched in luria broth medium containing RB-B dyestuff as a carbon source. Then biodegradation was assessed in 4 batch reactors. Microbial population of bacterial and decolorization quantities of samples were detected by MPN and UV-Vis spectrophotometer.
    Results
    Decolorization efficiency by the bacterial consortium was obtained more than 99% for 50 and 250 mg/L concentrations in 72 and 144 h (3 and 6 days) respectively, while for the initial concentration of 500 mg/L was 98.1in 240 h (10 days) of biodegradation period. Dyestuff reduction rate after completed removal was about 0.69, 1.74,2 mg/L/h for initial concentration of 50, 250, 500 mg/L respectively.
    Conclusion
    Results showed that Alcaligenes denitrificans and Alcaligenes xylosoxidans bacteria which were isolated from activated sludge have good potential of RB-B dyestuff removal and this removal is depending on primary concentration of dye. Removal efficiency increased as primary concentration went up.
  • M.R. Samarghandi, M. Noori Sepehr, M. Zarrabi, M. Norouzi, F. Amraie Page 399
    Backgrounds and
    Objectives
    Treatment of colored wastewater is one of the important challenges of environmental engineers. Adsorption process is a key option for removal of organic matter from wastewater. The aim of present work was to investigate pumice stone as an adsorbent for removal of Acid Black 1 from aqueous solution.
    Materials And Methods
    Removal of Acid Black 1 by pumice stone was investigated. Acid Hyrdo Chloric(HCL) 1 N was used to increse adsorbent porosity. Various parameters such as pH, initial dye concentration and contact time were studied.
    Results
    Results showed that removal of Acid Black 1 was increased by increasing of contact time and initial dyeconcentration although it was decreased by increasing of pH. Experimental data was best fitted to Longmuir isotherm model (r2>0.98). Study of diffusion model revealed that intraparticle diffusion is rate-controlling step in removal of Acid Black 1 by pumice stone.
    Conclusion
    The results indicated that pumice stone was a dominant adsorbent for Acid Black 1 removal.
  • M.H. Dehghani, S. Nasseri, M. Ghaderpoori, A.H. Mahvi, R. Nabizadeh Nodehi Page 411
    Backgrounds and
    Objective
    Surfactants are one of the largest pollutants which exist in urban and industrial wastewaters. Large quantities of surfactants have entered to the environment since last decade due to increased use of synthetic detergent in industrial and home consumptions.In this study, the efficiency of UV/H2O2 process in removal of linear alkylbenzane sulfonate (LAS) from aqueous solutions was investigated.
    Materials And Methods
    In this study methylene blue active substane(MBAS)method and spectrometery were used to determine anion and residual surfactant respectively. In this study important variables were H2O2 concentration, initial concentration of surfactant, pH and duration of UV radiation. The effect of UV/H2O2 process on the degradation of LAS was analyzed statistically by using Multiple Linear Regression test.
    Results
    The resulted showed that after 20 minute, ultraviolet radiation solely removed 38.44 percent of Anionic detergent, Hydrogen peroxide showed no significant removal of detergent solution in the time course study. The efficiency of UV/H2O2 process in 10, 20 and 30 minute were to 86.2, 90 and 96.5 %, respectively.
    Conclusion
    The results showed that the efficiency of ultraviolet radiation and hydrogen peroxide process in anionic detergent was not significant thoogh it was considerable in combination process (UV/H2O2)
  • R. Fouladi Fard, A.A. Ebrahimi Page 419
    Background And Objective
    Nickel (II) and cadmium (II) are important in environmental pollutant. Biosorption of heavy metals can be an effective process for the removal and recovery of heavy metal ions from aqueous solutions because of the decrease in sludge problems, economical issues, high efficiency and compatibility with the environment.
    Materials And Methods
    power of wasted activated sludge have been contact with nickel (II) and cadmium (II) solutions in 0.25 and 0.75 milli molar invarious pHs and mixing pace, at 24-26 0C temperature on batch reactor system. After two hours (continuously 5-420 min in kinetic study) samples were analyzed with atomic absorption spectrophotometer.
    Results
    The kinetic study results show that equilibrium adsorption time for nickel (II) and cadmium (II) reached within 2 hr, but the profile curve of cadmium (II) biosorption was smoother than nickel (II) biosorption. Both metals adsorption followed the Langmuir model and the maximum adsorption capacity (qmax) for nickel (II) and cadmium (II) was 0.195 and 0.37 milli mole per gram respectively. The increase in pH resulted in adsorption increase for both metals. For cadmium (II) at 0.25 and 0.75 mMinitial concentration there was no adsorption at pH 2 where as nickel (0.25 mM) adsorption was observed at the same pH. The optimum mixing rate for both metals was 200 rpm and this effect was more obviously in greater concentration.
    Conclusion
    Like othe biosorbents, wasted activated sludge showed greater capacity for cadmium(II) biosorption than nickel (II). Cadmium (II) in modeling and biosorption characteristics study had more conformity than nickel (II).
  • V. Alipour, L. Rezaei Page 431
    Background And Objectives
    Dual media filters have two different layer beds consist of sand and Anthracite. Advantage of dual media filters is longer run duration and more filtration rate. The purpose of this study was to achieve a performable model to improve single media Filters in water treatment plants.
    Materials And Methods
    in this cross-sectional study, two pilots; mono and dual media were made and in a 5 month period samples taking were done. Total samples taken from input and output of each pilot, was 40. The samples then introduced for the measurment of turbidity and total organic carbon. Meanwhile the filters head loss also quantified in 40 times head loss measurement was done.
    Results
    Average turbidity removal in mono and two layer pilots were 63 and 65 percent respectively. Average removal of Total Organic Carbon in mono and two media pilots were 40 and 66 percent respectively. Head loss in dual and single media pilots were 0. 68 and 1.15 m respectively.
    Conclusion
    Although average torbidity removal disparity between two pilots was not significant the amount of total organic carbon removed was considerable. Average head loss in single media pilot was more than dual media type. Ratio of UFRV in dual media to mono media filter was 51:30 it shows that filtration rate capacity will be improved up to70 percent by changing media type
  • A. Maleki, A. Eslami Page 439
    Backgrounds and
    Objectives
    Water contamination with arsenic has been recognized as a serious problem and its epidemiological problems to human health have been reported. The objective of this study was to explore the possibility modified wheat straw using sodium bicarbonate for removing arsenic from aqueous solution.
    Materials And Methods
    Adsorption process was accomplished in a laboratory-scale batch with emphasis on the effect of various parameters such as pH, contact time, arsenic concentration and adsorbent dosage on adsorption efficiency. In order to understand the adsorption process, sorption kinetics and equilibrium isotherms were also determined.
    Results
    It was found that adsorption of the arsenic was influenced by several parameters such as arsenic initial concentration, adsorbent dosage and solution pH. Maximum absorption efficiency was achieved at pH 7. As expected the amount of arsenic adsorbed on wheat straw incresed as its concentration went up. Among the models tested, namely the Langmuir, Freundlich, and Dubinin Radushkevich isotherms, the adsorption equilibrium for arsenic was best described by the Langmuir and Freundlich models. It was also found that adsorption of arsenic by wheat straw followed pseudo second-order kinetics. Mean free energy of adsorption (15.8 kJ mol-1) indicates that adsorption of arsenic by wheat straw might follow a chemisorption mechanism. Desorption studies show that arsenic ions are strongly bounded with the adsorbent and exhibit low desorption.
    Conclusion
    It is concluded that that adsorption by modified wheat straw is an efficient and reliable method for arsenic removal from liquid solutions.
  • M. Meschi Nezami, H. Ganjidoust, N. Mokhtarani, B. Ayati Page 451
    Backgrounds and
    Objectives
    Owing to the fact that the major environmental problem is production of surplus sludge in wastewater treatment plant, reducing the volume of produced sludge was objective of this research.
    Materials And Methods
    An anaerobic-aerobic SBR with working volume of 10 L was used to make micro-organism adapted and a polymer production reactor (PPR) with working volume of 1.5 L was used for producing polymer munisipal wastewater which contained different concentration of volatile fatty acids was consodered as the feed source (acetate and propionate) and this system was evaluated with SRT of 5, 7 and 10 days.
    Results
    The maximum polymer production efficiency observed within 5 days (SRT=5 days) though this efficiency was not significant in comparison with the two others time courses study. In this research the maximum polymer production efficiency at optimum condition was 25% of the sludge dry weight.
    Conclusion
    Experiment revealed that producing polymer from activated sludge reduced the volume of sludge and the maximum reduced sludge volume was obtained 19%.
  • A.R. Rahmani, M. Solaimany Aminabad, Gh Asgari, F. Barjasteh Askari Page 461
    Backgrounds and
    Objectives
    High level of nitrate ion in the water resources cause some health and environmental problems. The aim of this research is to study nitrate removal by Zero-Valent Magnesium (ZVM) and MgCl2-modified pumice from aqueous solutions.
    Materials And Methods
    The pumice granules were modified by MgCl2. The removal of nitrate was studied in a batch system. The pH, initial nitrate concentration and sorbent mass parameters and the Langmuir and Freundlich models were studied in the sorption of nitrate onto the pumice. The ZVM was also used in a bach system and the previous parameters were studied.
    Results
    The removal efficiencies of nitrate by ZVM at the the initial pH of 3, 5 and 7 with controlling the pH were 70%, 40% and 30%, respectively. These values are much higher than the values of the condition during which the pH was not controled. The nitrate removal efficiency increased by increasing of initial nitrate concentration in a constant molar ratio of Mgo/NO3. The removal efficiencies of nitrate by the modified pumice at the the initial pH of 3, 6.5 and 10 (when pH kept under control) were 49%, 29% and 16%, respectively. By increasing of the initial nitrate concentration the removal efficiency increased. The values of R2 for the Langmuir and Freundlich models were 0.944 and 0.810, respectively. The sorption process Fitted well the Langmuir model with a monolayer sorption capacity of 0.68 mg/g.
    Conclusion
    The modified pumice had lower efficiency than ZVM in the removal of nitrate ion and its usage is not considerably affected bye the pH in comparison with ZVM. The pH of the solution should be cansiderd as a main controling parameter to get an optimum efficiency in the nitrate-ZVM process.
  • I. Shakerinia Page 475
    Backgrounds and
    Objectives
    The aim of these research is examining the relation among noise psychological stubbornness and mental health with the life quality of rasht housewives.
    Materials And Methods
    After measuring the amount of noise in different streets, the researcher chose randomly 50 housewives from noisy streets of Rasht, and completed the study questionnaire. Then they analyzed data with peirson correlation and regression analysis.
    Results
    Theresultsshowedthat there is significant of perception of noise, psychological stubbornness and mental health with the quality of life. The amount of F parameter of regression analysis at P<0/01 level was significant and 91% of variance among noise with psychological stubbornness, mental health, with the quality of common life. Among the amount of noise, psychological stubbornness and mental health, the noise perception and mental health are able to making clear the quality of housewive's life; it means that increasing the amount variance of psychological stubbornness to equation wouldnt lead to increase significantly.
    Conclusion
    paying attention to the effectiveness variables like noise and psychological like mental health on quality of life, Societie's development and achievement and decreasing social services, present study suggest that all responsible organizations who work about societie's health are trying to set their programs forward to promote the quality of the whole society life and do this by decreasin.