فهرست مطالب

فصلنامه علوم و فناوری نساجی
سال چهارم شماره 2 (تابستان 1393)

  • تاریخ انتشار: 1393/05/20
  • تعداد عناوین: 6
|
  • روح الله سمنانی رهبر*، رضا قاسمی، مجتبی پوراصفهانی، جمیله آفاقی، ملیحه نازی، مهرداد آذین فر صفحات 3-8

    رفتار دو نمونه موکت نایلونی (معمولی و حاوی مواد بازدارنده شعله روی بورات)در برابر آتش مطابق استاندارد ISO 5660-1 و در شار گرمایی 35 kW/m2 بررسی شد. با استفاده از گرماسنج مخروطی، پارامترهای گرمایی واکنش در برابر آتش شامل زمان افروزش، کل گرمای آزاد شده، شدت و بیشینه گرمای آزاد شده، دود و خروج گازهای سمی بررسی شدند. نتایج نشان می دهد، زمان افروزش در موکت حاوی مواد شعله نسبت به موکت معمولی طولانی تر است، در حالی که بیشینه گرمای آزاد شده در موکت حاوی مواد بازدارنده شعله حدود %33 کمتر است. بدین ترتیب، خطرگسترش شعله در موکت حاوی مواد بازدارنده شعله در مقایسه با موکت معمولی کمتر است. بهبود رفتار در برابر آتش در موکت حاوی مواد بازدارنده شعله را می توان به تشکیل لایه زغال روی سطح سوخته و وجود افزودنی های مختل کننده واکنش های احتراق نسبت داد که موجب کند شدن واکنش های سوختن می شود و در نتیجه مقدار بیشینه گرمای آزاد شده کاهش می یابد.

    کلیدواژگان: رفتار اشتعال پذیری، گرماسنج مخروطی، موکت نایلونی، تکمیل ضد آتش، بیشینه گرمای آزاد شده
  • مهدی صفی صفحات 9-15
    رفتار نوری و رنگی الیاف معمول در نساجی که دارای خواص بازتاب سطحی و انتشارهای درونی قابل توجهی هستند، به طور تقریبی با تقریب مناسبی طبق نظریه تک ثابتی Munk -Kubelka قابل پیش بینی است. عوامل مختلفی از بازتاب سطحی و بازتاب نمونه خودرنگ نتایج به دست آمده را تحت تاثیر قرار می دهند. در پژوهش حاضر، اثر بازتاب سطح و بازتاب بستر خودرنگ مجموعه ای رنگی شامل الیاف نایلون 6 رنگرزی شده با مواد رنگزای اسیدی و پراکنده در غلظت های مختلف در کاربرد نظریه Munk -Kubelka روی منسوجات بررسی شده است. نتایج نشان داد، ارزش وجود بازتاب سطح و اطلاعات بستر خودرنگ در مطالعه رفتار رنگرزی منسوجات با مواد رنگزای مختلف به شدت تابع ناحیه غلظتی به کار گرفته شده است. این بدین معنی است که در بازتاب های نسبتا کم، مقدار بازتاب سطح تا حدی بسیار زیادی به بازتاب بستر رنگرزی شده نزدیک می شود و این اختلاف اندک، مقدار K/S بسیار بزرگی را نتیجه می دهد. افزون بر این نتیجه شد، ارزش بازتاب بستر خودرنگ به نحو محسوسی با افزایش جذب نمونه رنگرزی شده در نتیجه افزایش غلظت رنگزا کاهش می یابد.
    کلیدواژگان: نظریه تک ثابتی، Kubelka، Munk، منسوجات، رنگرزی، بازتاب سطح، بسترخودرنگ
  • مطهره کارگربیده، پدرام پیوندی صفحات 17-28
    طراحی مارکر از مهم ترین مراحل در بخش برش الگو صنعت پوشاک است. این فرایند در دسته مسائل تعیین شرایط بهینه ای است که هدف اصلی آن کشف آرایش و چیدمان مناسب از قطعه های متعدد الگو روی لایه های پارچه است. هدف مرسوم این مرحله بیشینه کردن بهره برداری، کمینه کردن دورریز پارچه و نیز کاهش زمان محاسبات است. چیدمان مارکر به عنوان موضوع مبتلا به صنعت پوشاک در گروه مسائل چیدمان دو بعدی نواری شکل های نامنظم قرار می گیرد. این عملیات به یافتن آرایش مناسب از چیدمان مجموعهای از قطعه های دوبعدی بر سطحی با عرض ثابت و طول نامحدود منجر می شود. در این مقاله، انواع الگوریتمهای ابتکاری و فراابتکاری که در حل مسائل چیدمان دو بعدی شکل های نامنظم توسعه یافته اند، مرور شده است.
    کلیدواژگان: مارکر، چیدمان، الگوریتمهای ابتکاری و فراابتکاری
  • علی صالحی راد، محمدرضا طبیبی، محسن عسگری، فاطمه جابری صفحات 29-33
    مهم ترین مسئله ای که از ابتدا خلقت انسان همواره مطرح بوده است، نیازهای نامحدود بشر و منابع محدود برای برآورد آن است. به دلیل محدودیت منابع است که به اجبار نمی توان در همه صنایع یا زیربخش های آن به شکلی یکسان سرمایه گذاری کرد و مسئله اولویت بندی آنها مطرح می شود. توسعه پایدار، هدف اصلی بسیاری ازکشورها بوده و توسعه مبتنی بر حفاظت و استفاده بهینه از همه منابع موجود است وصنعت نساجی و چرم به راحتی می تواند زیرساخت های مورد نیاز آن را ایجاد کند. در پژوهش حاضر، با در نظر گرفتن این حقیقت چالش های پیش روی توسعه صنایع نساجی و چرم به روش تحلیل محتوای اخبار موجود در رسانه ها طی سال های 1391- 1390 شناسایی شد. در این راستا مطالب ارائه شده توسط مدیران خصوصی و دولتی، کارشناسان و صاحب نظران با حداقل 5 سال سابقه کار مستمر و مطرح از تارنما های معتبر خبری جمع آوری و بر اساس تعریف عملیاتی متغیرها کد گذاری شد. در نهایت، بر اساس فراوانی تکرار و تاکید بر این واژگان مقدار اهمیت آنها مشخص شد. باتوجه به نتایج تحلیل و از میان شاخص های بررسی و شناسایی شده در صنعت، قابلیت های بازاریابی و اندازه صنعت به عنوان مهم ترین شاخص های داخلی و رقابت و ساختار بازار و دولت و مقررات به عنوان مهم ترین شاخص های خارجی صنعت شناسایی شدند.
    کلیدواژگان: نساجی و چرم، موانع و راهکارها، توسعه صنعت، تحلیل محتوای اخبار
  • محمد سجاد سرایانی بافقی، علی غیبی، روح الله باقرزاده، مسعود لطیفی صفحات 35-38
    منابع انرژی مکانیکی کوچک متنوعی در محیط اطراف ما وجود دارد که به سادگی نادیده گرفته میشود، هرچند مقدار آنها جزئی است. اما، در مجموع مقدار این انرژی ها قابل توجه است. برداشت انرژی الکتریکی از منابع محیطی پیرامون ما و استفاده از آن برای تامین انرژی الکتریکی این ابزارهای قابل حمل بسیار مورد توجه است. از طرفی پیزوالکتریکها، موادی هستندکه قابلیت تبدیل انرژی مکانیکی والکتریکی به یکدیگر را دارند و به عنوان یکی از گزینه های مناسب برای استفاده در ابزارهای خود شارژ شونده مطرح هستند. در پژوهش حاضر، روشی برای تولید نانومولدهای الیافی انعطاف پذیر با تکیه بر خواص پیزوالکتریکی مواد و استفاده از پیزوپلیمرها و تلفیق آن با نانوفناوری ارائه شده است. انعطافپذیری زیاد نانومولد انعطاف پذیر، امکان استفاده ازآن در منسوجات، به ویژه البسه را برای تامین انرژی الکتریکی مورد نیاز وسایل میکروالکترونیک همراه فراهم میسازد. بدین منظور، از فرایند الکتروریسی برای تولید الیافی با ابعاد نانو و میکرو از محلول پلی وینیلیدن فلوئورید استفاده شد. لایه الیاف تولیدی به روش های مختلف نظیر پراش پرتو X (XRD) برای بررسی ساختاربلوری،میکروسکوپی الکترونی پویشی(SEM) به منظور بررسی ساختار ظاهری و یکنواختی نانو الیاف وآزمون اندازه گیری ولتاژ خروجی ارزیابی شد. نتایج حاصل حاکی از امکان استفاده از این محصول به عنوان نانومولداست. مقایسه توان خروجی نانومولدتولیدشده و لایه های پلی وینیلیدن فلوئورید نشان داد، ولتاژ و جریان قابل برداشت بهبود چشمگیری دارد و این مقدار از 0.5V و 0.6 pA مرتبط با یک فیلم پلی وینیلیدن فلوئورید به 3.4 V و 3mA بهبود یافته است.
    کلیدواژگان: الکتروریسی، نانوالیاف، نانومولد، پیزوالکتریک
  • رامین عبقری، مجتبی دربیدی صفحات 39-45
    در فرایند ریسندگی، ابزارهای راهنمای نخ، آثار بسیاری روی کیفیت نخ به جا می گذارند و در بسیاری از موارد حتی، سبب کاهش کیفیت نخ تولیدی می شوند. به طور معمول این نوع اثرهای منفی، در سانانه های منتهی به دستگاه بوبین پیچی مشهودتر است. درماشین های جدید بوبین پیچی، برای کاهش پرزینگی نخ از سازوکاری با نام بالکن استفاده می شودکه مقدار پرزینگی را در سرعت های زیاد به نسبت کاهش می دهد، دلیلی که سبب شد، طراحی جدیدی روی ماشین های قدیمی بوبین پیچی اجرا شود و در آن با به کارگیری سامانه ای مشابه با بالکن، روشی برای تغییرساختار هندسی ناحیه بالن نخ دربوبین پیچی انجام شود. طراحی سامانه ای که سرانجام با اندازه گیری دقیق ناحیه باز شدن بالن در ماشین بوبین پیچی و با استفاده ازجنس های مختلف و طراحی های متفاوت بالن گیر روی سامانه ریسندگی پنبه ای نصب و استفاده شد. نتایج پژوهش از کاربرد این نوع بالکن طراحی شده، در آزمون های یکنواخت سنجی و پرز سنجی نشان می دهد، در سامانه ریسندگی الیاف کوتاه، بهبودکیفیت نخ در حد قابل قبولی انجام شده است. ازاین رو،استفاده از این سازوکار برای سامانه ریسندگی الیاف کوتاه، به ویژه روی ماشین هایSchlafhorst پیشنهادمی شود.
    کلیدواژگان: سامانه بالکن، ماشین بوبین پیچی، پرزسنج Keissoki، نایکنواختی نخ
|
  • Ruhollah Semnani Rahbar Pages 3-8

    Flammability properties of two nylon moquette samplse (i. e. raw and zinc borate flame-retarded) were investigated by cone calorimeter equipment in accordance with the ISO 5660-1 test procedure at irradiance (heat flux) of 35 kW/m2. Fire behavior parameters such as ignition time، heat release rate، total heat evolved، specific extinction area، carbon monoxide yield، and carbon dioxide yield were obtained by measuring oxygen consumption and considering the related equations. The results showed that for the flame-retarded moquette، the peak heat release rate (PHRR) was reduced 33% and the time of ignition (TTI) was delayed 16 s compared with those for the raw moquette. The assessment results revealed that the flame-retarded moquette has a lower contribution to bring room to critical flashover condition. This remarkable behavior might be explained by formation of a compact، dense and uniform char from combustion and also disturbance in combustion reactions due to the flame-retardant additive.

    Keywords: Flammability properties, Cone calorimetry, Nylon 6 moquette, Flame retardant, Peak heat release rate
  • Pages 9-15
    Color and optical properties of typical fibers of textile that benefit specific surface reflectance and internal scattering properties can be estimated according to the single-constant Kubelka-Munk theory. Various factors such as surface reflectance and mock dyed substrate may affect the measured reflectance of dyed samples. In the present study، a series of fiber 6 were dyed with acid and disperse dyes in different concentrations and the effect of surface reflectance and the reflectance of mock dyed substrate on the application of Kubelka-Munk theory for textiles have been investigated. The results showed the extent of the impact of the surface reflectance and the reflectance of mock dyed substrate is deeply dependent to applied dye concentration. It means that at relatively low reflectance، the surface reflectance values gets close to the reflectance of the dyed substrate. Consequently، the very large quantities for cquires. In addition، it was concluded that the influence of the reflectance of mock dyed substrate significantly decreases by increasing the dye concentration range.
    Keywords: Single, constant Kubelka, Munk theory, Textiles, Dyeing, Surface reflectance, Mock dyed substrate
  • Pedram Payvandy Pages 17-28
    Marker planning is a critical operation in the cutting-fabric stage in the clothing industry. This is among those optimization problems that is concerned with finding a good arrangement of multiple pattern pieces on fabric. The goal of this process is to maximize the utilization productivity and as a result to minimize the waste of fabric and reduce the computing time. Cutting and packing problem in textile industry should be considered as a two-dimensional (2D) strip packing of irregular shapes and finding a proper arrangement among packing of a limited set of 2D components on a fabric surface with fixed width and infinite length. This paper reviews the types of heuristic and etaheuristic algorithms that have been developed for solving 2D packing of irregular shapes.
    Keywords: Marker, Packing, Heuristic, meta, heuristic algorithms
  • Ali Salehirad, Mohammad Reza Tabibi, Mohsen Askari, Fatemeh Jaberi Pages 29-33
    The main problem that has existed from the beginning man''s creating is human unlimited needs and limited resources in order to resolve that. Because of limited resources، it is not possible to invest in all industries and subdivisions in a same way and therefore investment priorities is discussed. Sustainable development is one of the main goals of many countries and the development is based on the conservation and efficient use of all existing resources and the textile industry stakeholders can easily create required infrastructures. In the present study، with considering the potential in textile industry for sustainable development، the challenges facing the textile and leather industries have been identified using news and media content analysis during the period 1390-1391. For this purpose، the contents regarding textile industry provided by managers in public and private sectors، textile experts and well-known clear-sighted individuals with at least 5 continuous years of experience were gathered from reputable news sites. The extracted contents were coded based on the operational definition of variables. Finally، based on the abundance of repeat and emphasize on these coded vocabularies، their importance was determined. The results showed that marketing capabilities and industry value are among the most important internal criterion and competition، market structure، government and rules are among the most important external criterion for textile industry.
    Keywords: Textile, leather, hindrances, procedures, industry development, content analysis of news
  • M. Sajad S. Bafqi, Ali Gheibi, R. Bagherzadeh, Masoud Latifi Pages 35-38
    We are surrounded by various small mechanical energy sources which are normally ignored. Although their individual level of energy is quite low، the total amount of energy produced should be considered significance. Utilization of these energies that have so far been neglected can be very useful، especially for charging portable and wireless electronic devices that they should be charged frequently. Supplying electrical energy needed for the microelectronic devices can also be of the great importance from the environment point of view. Piezoelectric materials are able to convert mechanical to electrical energy (and vice versa) and can be considered as the best choice for harvesting energy devices. However، they are thick and rigid and have a low efficiency in the form of polymeric films. In this paper، an attempt is made to fabricate a flexible nano-generator using piezoelectric properties of polyvinylidene fluoride (PVDF) for harvesting electrical energy. The flexibility of polymer can be useful for fabrication of self-chargeable microelectronics and suitable for using in the wearable textile. Electrospining was used for fabrication of PVDF nanofibers. XRD، SEM and V-Out results showed that the flexible nano-generator based on PVDF nano-fibers could be fabricated and utilized in the smart clothing sectors for supplying the electrical power. The results of output voltage and current of both PVDF thin fim (0. 5 V، 0. 6 pA) and nano-fiber mat (3. 4 V، 3 mA) show a considerable improvement of V-out for the nano-fiber mat vs. film which is promising for energy harvesting piezoelectric material.
    Keywords: Electrospinning, Nanofiber, Nanogenerator, Piezoelectric
  • Ramin Abghari, Mojtaba Dorbidi Pages 39-45
    In spinning processes، bobbin winding yarn guide tools are effective on the yarn quality and in most cases reduce the yarn quality. This is more pronounced at the end of spinning process especially in winding machine. In new bobbin winding machines، yarn hairiness is reduced at high speed by Bal-Con mechanism. So، in the present study Bal-Con system in old bobbin winding machine was modified according to the concept of Morata-Tech Bal-Con system and the geometry structure of the bobbin winding process region was changed accordingly. In the first step evaluated more accurate balloon region. In new bobbin winding machines، a mechanism called Bal-con is used to reduce yarn hairiness and it reduces hairiness at high speed as acceptable. Based on this issue، a new design was performed in old bobbin winding machines in which a method is used to change the geometry of yarn balloon in bobbin winding. At first، the balloon control region was measured exactly in bobbin winding machine. Then، by various types and different designs of Bal-con، the best Bal-con design was selected and used in cotton spinning system. The results of the study showed that based on evenness and hairiness tests and designed Bal-con، in short fibers spinning system، the yarn quality is improved. Therefore، this mechanism is proposed for spinning system of short fibers namely on Schlafhorst machines.
    Keywords: bal, con system, cone winding machine, keissoki hairiness, yarn unevenness