International Journal of Civil Engineering
Volume:13 Issue: 1, Mar 2015

Many buildings in urban areas adjacent to excavations are damaged by ground movements due to limitations in design methods of support system. A traditional support system that is used in different areas of Iran, in which, inclined struts are connected to the wall or foundation of neighboring buildings. So this method can be considered as shoring or underpinning. In this paper, firstly the concept of performance of building and criteria of deformation control in excavation are introduced. Secondly, a two dimensional finite element analysis is presented, in which excavation is modeled with neighboring buildings and inclined struts. Finally, the effect of different variables on the performance and also the limits which inclined strut has acceptable performance are discussed. Analysis shows the stiffness of building, depth of excavation and the soil stiffness prove to have significant effect on the performance of building. In addition, cohesion of soil can seriously reduce the horizontal wall deflection and consequently limit damage of neighboring building. Inclined strut affects the performance of a building beside an excavation through two mechanisms: (a) inclined struts transfer a fraction of neighboring building loads and reduce excavation induced settlements. (b) Inclined struts limit the horizontal displacement and thereby can consequently reduce building damage.

Stabilization of earth slopes with various proposed methods is one of the important concerns of geotechnical engineering. In this practice, despite numerous developments, design conservativeness and high costs of stabilization are the issues yet to be addressed. This paper not only deals with pile location optimization but also studies the effects of the pile length by using line segments slip surface (non-circular). Taking into account the line segments slip surface in stabilization of earth slopes is a new topic which has been addressed in this paper. The line segments slip surface is actual slip surface and for determining the pile location it can lead to the actual length of the pile. The line segments critical slip surface is obtained by using the Alternating Variable Local Gradient (AVLG) optimization method. AVLG is an approach in optimization process and it is based on the Univariate method. The line segments form the initial and critical slip surface. Pile improper installation and inadequate length not only fails to increase the factor of safety, but also reduces it. The analyses are performed using the limit equilibrium (LE) method. Results of these analyses are acceptable and are properly consistent with the results obtained by other researchers.

Investigation of projectiles penetration phenomenon has been carried out in non-cohesive soil (Sand) targets under dry, saturated and compacted conditions. Analytical studies have been performed on the linear and non-linear soil models to obtain penetration depth formulae for ogival nose projectile and the results are verified by experimental studies. In present work, three ogival nose projectiles each having weight of 1.0 kg and nose angle of 15o, 30o and 45o are dropped from a height of 10.0 m in rectangular tank filled up by non-cohesive soil target. The rigid projectiles made an impact on a uniform target material at normal incidence with striking velocity of 14 m/s and proceeded to penetrate at rigid-body velocity. The models require geometrical parameters of the projectile types, velocity and target shear strength for the overall penetration depth of projectile. In addition, some parametric studies have been also carried out for academic and field interest.

To investigate the saturation induced collapse deformation behavior of rockfill material, a set of large-scale triaxial tests were conducted in saturated and dry-saturated conditions. Specimens were tested under various confining pressures. For drysaturated tests, specimens were sheared in various stress levels. Results of all dry saturated tests indicate a sudden reduction in the specimen volume during the submerging process. The ratio of the minimum axial strength of a submerged specimen (at the end of the saturation process) to the shear strength of the specimen before saturation is defined as the coefficient of stress recovery, Csr. Results show that this ratio increases as the confining pressure increases, and decreases as the shear stress level increases. According to the results of dry-saturated tests, reduction values of the internal friction angle caused by saturation (c), the ratio of the elasticity modulus of the material after saturation to its elasticity modulus in dry condition, i.e., Ewet/Edry, and the saturation induced sudden volumetric strain (vc) decrease as the confining pressures increase. However the shear stress level does not have any meaningful effect on the variation of c, Ewet/Edry and (vc).

The use of recycled bassanite, produced from gypsum wastes, in ground improvement projects is initiated recently in Japan to eliminate the huge quantities of gypsum wastes. Meanwhile the use of recycled bassanite has a positive effect on the environment and economy, it has many challenges. These challenges are related to the release of fluorine more than the standard limits results in contaminated fluorine soil. This research investigates the effect of the amount of bassanite, and water content on the release of fluorine from MC-clay soil stabilized with bassanite, taking in consideration their effect on the compressive strength. Recycled bassanite was mixed with furnace cement with a ratio of 1:1 to prevent the solubility of bassanite. Different amounts of this admixture were mixed with the tested soil at different water contents. Unconfined compression test was used to determine the compressive strength while the solubility of fluorine was used to represent the geoenvironmental properties in term of the release of fluorine. Scan electron microscopic (SEM) test was done to identify the development of cementation compounds in the matrix of treated-bassanite soil. Test results showed that, the addition of bassanite had a significant effect on the improvement of compressive strength by increasing the amount of bassanite. Curing time had a significant effect on the increase of compressive strength, the strength increases with the increase of curing time, especially in the later curing time. The release of fluorine increases with increasing the amount of bassanite in soil mixture. The increase of water content had an indirect effect on the release of fluorine while it had a negative effect on the improvement of strength and consuming the amount of admixture. The increase of strength is associated with the decrease of the release of fluorine. Recycled bassanite, produced from gypsum wastes, had a potential to be used as a stabilizer material for MC-clay soil and meet the standards of environment.

In this paper we are going to show the importance of mode identification in microtremor array analysis. The idea come from four concentric ambient noise array recordings with aperture 100 to 1000 meters, performed in southern urban area of Tehran near the shrine of Imam Khomeini. These measurements were part of a comprehensive research project with the aim of determination of deep shear wave velocity model of Tehran alluvial deposits. Using appropriate signal processing techniques, including array processing methods as well as classical and time-frequency horizontal/vertical spectral ratio, the dispersion curves of surface waves, fundamental resonance frequency and Ellipticity of Rayleigh waves, were extracted. In the final step, the shear wave velocity profile of the site was determined by joint inversion of all of these attributes. The results show 2 different energetic trends in dispersion curves, for arrays of aperture 200 and 400 meters that one of them is coincide with 100m aperture array. For array with aperture 1000m any clear trend of energy could be observed because of deficiency of energy in low frequency. The inversion of data obtained by 100m aperture array alone, assuming the dispersion curve as fundamental mode (a common procedure in urban area) result in shear wave velocity that is not match with existing geological information. Performing the inversion, assuming 2 energetic trends, observed for larger arrays; one as fundamental mode and another as mode 1 of Rayleigh waves, can modify significantly the shear wave velocity profile in accordance with existing geological and geotechnical information. This study show the importance of extracting of correct dispersion curves with detecting fundamental and higher modes, using array measurement with various aperture at one place to obtain more realistic shear wave velocity profile.

We report engineering experiences from the critical task of relief well installation under high artesian flow conditions at the downstream toe of the Karkheh earth dam, Iran. Due to the establishment of excessive uplift pressure at the downstream toe of the Karkheh dam, installation of a series of new relief wells was considered to permanently relieve part of these pressures. The mentioned uplift pressure, as high as around 30 m above the ground level, was produced in a confined conglomerate aquifer bounded above and below by relatively impervious mudstone layers which reduced the safety factor of the dam toe to below 1.0. Investigations on the shortcomings of the old relief wells installed at the dam site showed that the main problems were: insufficient well numbers, insufficient well diameters, irregular well screens causing their blockage by time passing, and insufficient total opening area. Despite engineering difficulties and associated risk of downstream toe instability, installation of new relief wells was successfully completed under high artesian flow conditions” was successfully completed. The employed technique for the construction of the new relief wells under flowing artesian conditions was based on: 1) cement grouting and casing of the well, 2) telescopic drilling, 3) application of appropriate drilling fluid, and 4) controlling the artesian flow by adding a long vertical pipe to the top of the relief wells. Numerical modeling of seepage for the Karkheh dam foundation showed that, as a result of the installation of the new relief wells, the safety factor of the downstream toe increased to the safe value of 1.3 for the normal reservoir water level.