به جمع مشترکان مگیران بپیوندید!

تنها با پرداخت 70 هزارتومان حق اشتراک سالانه به متن مقالات دسترسی داشته باشید و 100 مقاله را بدون هزینه دیگری دریافت کنید.

برای پرداخت حق اشتراک اگر عضو هستید وارد شوید در غیر این صورت حساب کاربری جدید ایجاد کنید

عضویت
جستجوی مقالات مرتبط با کلیدواژه

continuous flow

در نشریات گروه پزشکی
تکرار جستجوی کلیدواژه continuous flow در مقالات مجلات علمی
  • Seyed Javad Hosseini, Fereshteh Eidy, Majid Kianmehr, Ali Asghar Firouzian, Fatemeh Hajiabadi, Mahmoud Marhamati, Mahbobeh Firooz*
    Introduction

    Peripheral intravenous catheters (PICs) patency techniques such as flushing are being developed. According to some studies, flushing can be used continuously or in pulsatile forms. This study aimed to compare the effects of pulsatile flushing (PF) and continuous flushing (CF) on time and type of PICs patency.

    Methods

    In this double-blind randomized clinical trial, 71 patients were randomly assigned into two groups of PF (n=35) and CF (n=36). The PF protocol was performed as successive injections of 1 mL normal saline (N/S) per second (sec) with a delay of less than 1 sec until the completion of 5 mL of solution. However, CF protocol was performed by injecting 5 mL N/S within 5 sec without any delay before and after each medicine administration. Data related to the time and type of PICs patency were collected using a patency checklist every 12 hours (h) up to 96 h. The statistical analysis was done by R statistical software (Version 3.5.1).

    Results

    The results showed that the number of PICs remaining open was not significantly different between PF and CF groups during 96 h. The highest number of PICs excluded from the study was related to the time of 96 h as a result of partial patency in the two groups.

    Conclusion

    There was no difference between CF and PF regarding the time and type of PICs patency. Thus, both techniques can be used to maintain the catheter patency.

    Keywords: Pulsatile flow, Continuous flow, Peripheral Catheter, Vascularpatency, Flushing
  • Ali Akbar Rahmani Sarmazdeh, Mostafa Leili*

    This research mainly aimed to investigate phosphorus removal from stabilization pond effluent by using anionic resins in the continuous flow mode of operation due to high amounts of phosphorus in the wastewater treatment plant effluent of Kaboodrahang, western Iran, as well as the violation from a prescribed effluent standard to discharge receiving the surface waters. For this purpose, the pilot was made of a plexiglass cylinder and other equipment such as pump and other accessories, as well as Purolite A-100 resin. The reactor effects on the desired study parameters were assessed in two warm and cold seasons. The results showed that the phosphorus concentrations reduced from 7-10 mg/L to 4-7 mg/L and the rate of phosphorus removal was higher in the hot season compared to the cold season. Moreover, the optimum temperature and pH were obtained 21ºC and 8.5, respectively. The mean inlet biological oxygen demand (BOD) was 150 mg/L for both warm and cold seasons, where the highest removal rate of 17% was obtained in the cold season. The mean chemical oxygen demand concentration of the pilot was 250 mg/L for both seasons, and the highest removal rate was observed in the cold season with an efficiency of 18%. Regarding the total suspended solids with the mean inlet of 230 mg/L, the highest removal efficiency was obtained 6% in the warm season.

    Keywords: Phosphorus, Stabilization pond, Continuous flow, Anionic resin
  • Elhameh Mohammadpour, Mohammad Reza Yaftian, Abasali Zamani, Parvin Gharbani*
    Background & Aims of the Study: Heavy metals discharge to environment is a worldwide problem growing in scale. When they accumulate in the environment and in food chains, they can profoundly disrupt biological processes. Peganum Harmala Seeds (PHS) was used as a bio-sorbent, using a continuous system for removing Pb2, Co2, Ni2 and Cu2 ions from aqueous solutions.
    Materials And Methods
    PHS was used as adsorbent in adsorption of heavy metals from aqueous solutions. A stock solution of Pb(II), Co(II), Cu (II) and Ni (II) was prepared and experiments were down in a column as a reactor. The concentration was determined by atomic adsorption spectroscopy. The effect of various parameters such as pH, contact time, heavy metal concentration, ionic strength, particle size and adsorbent dosage on the process was investigated. Langmuir, Frundlich and Temkin isotherms were studied to evaluate of adsorption isotherms.
    Results
    The adsorption efficiency was found to be pH dependent and enhanced by increasing the solution pH. Maximum removal of ions were obtained at pH=4-8. The equilibrium time was attained after 30 min and desorption studies were performed, using diluted HNO3, H2SO4 and HCl solution (1M) on adsorbed metal ions from PHS. Results illustrated that adsorbed metal ions could be recovered under acidic conditions. Investigation of the process kinetic was best fitted with pseudo second-order model. Langmuir, Freundlich and Temkin models were tested for describing the equilibrium data. The Langmuir isotherm illustrated the best description of the cobalt and copper adsorption mechanism and Freundlich model describes lead and nickel ions adsorption on PHS.
    Conclusion
    It was found that PHS would be a good adsorbent for removal of heavy metals.
    Keywords: Peganum harmala seeds, Adsorption, Adsorbent, Continuous Flow, Heavy Metals, Iran
  • مهدی صادقی*، کاوه خسروی، سید مصطفی خضری، ابوطالب بای
    زمینه و هدف
    امروزه به دلیل گسترش روزافزون صنایع و نیاز گسترده به آب در فرایند تولید، انواع فاضلاب ها با بار آلودگی بالا تولید می شوند. لذا این مطالعه با هدف تعیین کارآیی الکتروکواگولاسیون در تصفیه فاضلاب صنایع لبنی به صورت جریان پیوسته ( مطالعه موردی فاضلاب ورودی کارخانه پنیر صباح گنبد کاووس) طراحی و اجرا گردید.
    روش کار
    مطالعه به صورت توصیفی تحلیلی با رویکرد آزمایشگاهی انجام شد. نمونه ها از فاضلاب ورودی کارخانه پنیر صباح برداشت و وارد راکتور الکتروکواگولاسیون با جریان پیوسته شد و در زمانهای ماند مختلف 20، 40 و 60 دقیقه و جریان الکتریسیته با ولتاژهای 20، 40 و 60 ولت آزمایشات COD، BOD، کدورت، نیترات، فسفات انجام و نتایج حاصله آنالیز گردید.
    یافته ها
    میانگین COD ، BOD ، نیترات، فسفات و کدورت به ترتیب در فاضلاب کارخانه صباح به طور متوسط برابر 231±4933، 50±600 ، 8/14±6/48 ، 7/0±28میلی گرم در لیتر و NTU 6/297±1329بود. بیشترین میزان حذف این پارامترها در طول انجام مطالعه با توجه به زمان واکنش و میزان پتانسیل الکتریکی به ترتیب 62/84، 67/66، 55، 2/54 و 1/85 درصد بود.
    نتیجه گیری
    با توجه به نتایج مشخص شد که فرایند انعقاد الکتریکی به عنوان فرایند پیش تصفیه می تواند باعث حذف مواد آلی ،کدورت ، مواد مغذی ، کاهش بار آلی و افزایش تجزیه پذیری فاضلاب گردد و می تواند به عنوان گزینه ای موثر جهت تصفیه موثر فاضلاب ها ، جلوگیری از آلودگی محیط زیست ، منابع آب و حفاظت از آنها مد نظر قرار گیرد.
    کلید واژگان: الکتروکواگولاسیون، فاضلاب، صنایع لبنی، جریان پیوسته
    Mahdi Sadeghi*, Kaveh Khosravi, Seyed Mostafa Khezri, Abotaleb Bay
    Background And Objective
    Today, with the development, the need for water in the production processes is increasing and so we have sewage with high level of pollution. This study aimed at determining the effectiveness of electrocoagulation for treatment of dairy industry wastewater in a continuous flow (case study wastewater of Sabah cheese factory Gonbad-e Qabus).
    Materials and Methods
    This study was descriptive and analytical with experimental approach. The samples were collected from Sabah dairy factory and put into the electrocoagulation reactor with continuous flow. At retention times of 20, 40 and 60 minutes with an electric current of voltages 20, 40 and 60 were purged. The samples were carried to the laboratory and various tests of COD, BOD, pH, turbidity, nitrate and phosphate were done. Then the results were compared and analyzed.
    Results
    The mean of COD, BOD, nitrates, phosphorus and turbidity was 4933 ± 231, 600 ± 50, 48.6 ± 14.8, 28 ± 0.7 mg/L and1329 ± 297.6 NTU respectively. The most removal efficiency of these parameters during the study was 84.62, 66.67,55, 54.2 and 85.1 percent respectively.
    Conclusion
    This study showed that electrocoagulation process as a pre-treatment process can remove organic matters, turbidity and nutrients. It can also reduce organic load and increase wastewater biodegradability and it can be an effective option for treating wastewater effectively and thereby preventing pollution in our environment and water resources.
    Keywords: Electrocoagulation, Wastewater, Dairy industry, Continuous flow
  • علی نقی زاده، سیمین ناصری*
    زمینه و هدف
    مواد آلی طبیعی مخلوط پیچیده ای از پلی الکترولیت های با وزن مولکولی متفاوت هستند که عمدتا از تجزیه بقایای گیاهان و حیوانات تولید می شوند. مواد آلی طبیعی توسط روش های تصفیه مختلفی از آب قابل حذف است. هدف از مطالعه حاضر بررسی کارایی نانولوله های کربنی شکل دهی شده در حذف مواد آلی طبیعی از محلول آبی است.
    روش بررسی
    در این مطالعه برای حذف مواد آلی از نانولوله های شکل دهی شده در ستون جریان پیوسته استفاده شد. متغیرهای مختلفی از جمله pH نقطه صفر، pH، غلظت های مختلف مواد آلی طبیعی و همچنین ایزوترم ها مورد مطالعه قرار گرفت.
    یافته ها
    نتایج بررسی اثر pH نشان داد که ظرفیت جذب سطحی مواد آلی طبیعی با کاهش pH افزایش می یابد. pH نقطه صفر (pHZPC) برای نانولوله های کربنی مورد استفاده در این پژوهش برابر 6 بود. همچنین نتایج آزمایشات ایزوترم های فروندلیچ، لانگمویر و BET نشان داد که ضریب رگرسیون R2 برای ایزوترم فروندلیچ نسبت به دو ایزوترم دیگر برای نانولوله های کربنی مورد استفاده در این تحقیق بالاتر بود. آزمایشات ستون جذب پیوسته در غلظت های مواد آلی طبیعی ورودی مختلف نشان داد که ظرفیت جذب سطحی نانولوله های کربنی برای غلظت های مواد آلی طبیعی ورودی 10، 5 و mg/L 3 به ترتیب برابر 53/46، 30/40، mg/g 24/75 بود.
    نتیجه گیری
    از نتایج این مطالعه می توان نتیجه گرفت که نانولوله های کربنی شکل دهی شده جاذب موثری برای حذف مواد آلی طبیعی از محلول آبی است.
    کلید واژگان: نانولوله های کربنی، شکل دهی، مواد آلی طبیعی، جریان پیوسته
    A. Naghizadeh, S. Nasseri*
    Background And Objective
    Natural organic matters (NOMs) are a mixture of chemically complex polyelectrolytes with varying molecular weights, produced mainly from the decomposition of plants and animal residues. Various purification methods are used for removal of NOMs from water. The objective of this study was to remove NOMs from aqueous solution using reformed continuous carbon nanotubes column.
    Materials And Methods
    The removal of NOMs from aqueous solution using reformed continuous carbon nanotubes column was studied. Effect of several variables such as zero point of pH (pHZPC), pH, influent concentration of natural organic matters were studied and different isotherms were assessed.
    Results
    Investigation of pH effect showed that the adsorbability of NOMs increased with decreasing of pH. The experiments indicated that carbon nanotubes (CNT) samples exhibit pHZPC around 6. Results from Freundlich, Langmuir, and BET isotherm experiments revealed that the correlation coefficient R2 in Freundlich model was higher than that of Langmuir. In addition, experiments of continuous flow in different initial concentrations of NOMs showed that the adsorption capacities of CNT were 53.46, 30.40, and 24.75 mg/g for NOMs initial concentrations of 10, 5, and 3 mg/L, respectively.
    Conclusion
    The present study shows that CNTs have high potential for adsorption of NOMs from aqueous solution.
    Keywords: carbon nanotubes, reformation, natural organic matters, continuous flow
  • محمدحسین سلمانی ندوشن، محمدحسن احرام پوش، حسین مسعودی، محمد تقی قانعیان، محسن عسکرشاهی
    مقدمه
    انتشار فلزات سنگین در محیط زیست ناشی از صنعتی شدن و شهرنشینی، یک مسئله نگران کننده در سراسر جهان می باشد. یون کادمیوم یکی از فلزات سنگین غیر ضروری، غیر مفید و خیلی سمی برای انسان، حیوانات و گیاهان است که حداکثر غلظت مجاز آن 005/0 میلی گرم در لیتر توسط WHO تعیین شده است. روش های مختلفی برای حذف فلزات سنگین مطالعه شده اما استفاده از جاذب های ارزان قیمت برای حذف این فلزات در سال های اخیر مورد توجه پژوهشگران قرار گرفته است. در این تحقیق روش جریان پیوسته را برای حذف یون کادمیوم از محلول های آبی توسط جاذب تهیه شده از ساقه جو مطالعه شد.
    روش بررسی
    این مطالعه تجربی آزمایشگاهی در سال 1390 انجام شد. ذرات ساقه جو در محدوده 19/1 تا 2 میلیمتر در ستونی با جریان روبه پایین برای حذف یون کادمیوم مورد بررسی قرار گرفت. در این بررسی pH برابر 6 ودمای C ° 27 آزمایش ها ثابت بود واثر متغیرهای غلظت اولیه ورودی، دبی جریان ورودی و ارتفاع بستر جاذب بر میزان حذف یون کادمیوم مطالعه شد. برای هر آزمایش مقدار 6 میلی لیتر نمونه در زمان های 30 دقیقه از خروجی ستون جمع آوری و غلظت یون کادمیوم در هر نمونه با دستگاه جذب اتمی اندازه گیری شد.
    یافته ها
    نتایج آزمایش ها نشان داد که منحنی شکست ستون جاذب به متغیرهای مطالعه شده وابسته است. افزایش دبی و غلظت، زمان رسیدن به نقاط شکست و اشباع جاذب راکوتاه تر و افزایش عمق بستر آنرا طولانی تر می کند. ماکزیمم یون کادمیوم جذب شده بر روی جاذب mg/g 07/10در شرایط دبی ml/min 3، عمق بستر cm 30 و غلظت اولیه mg/l 30 بدست آمد.
    نتیجه گیری
    با توجه به نتایج بدست آمده، با افزایش دبی ورودی میزان ظرفیت جاذب و راندمان جذب کاهش می یابد. در دبی ورودی ml/min 2 یون کادمیوم بخوبی از روی ستون با جاذب ساقه جو حذف می شود.داده ها نشان دادند که این جاذب برای جذب یون کادمیوم ظرفیت جذب نسبتا بالایی دارد. لذا پیشنهاد می شود روش جریان پیوسته با پارامترهای بدست آمده در این مطالعه در فرآیند تصفیه شیمیایی آب وفاضلاب مورد بررسی قرار گیرد.
    کلید واژگان: جاذب طبیعی، جریان پیوسته، ساقه جو، محلول های آبی، یون کادمیوم
    Mh Salmani, Mh Ehrampoush, H. Masoudi, Mt Ghaneian, M. Askarshahi
    Background
    Releasing of heavy metals in the environment caused by industrialization and urban، is a concern worldwide. Cadmium ion is toxic contaminants for Humans، Animals and plants that the maximum allowable concentration in water (0. 005 mg/l) is defined by WHO. Different methods for removing heavy metals have been studied. In recent years، the use of low-cost adsorbent for removal of these metals has been considered by researchers. In this study، removal of cadmium ions from aqueous solutions with continues flow method was studied by prepared adsorbent from barley stems.
    Methods
    This experimental- laboratory study done in 2011. Barley stem particles in the range of 1. 19 to 2 mm were investigated for removal of cadmium ions with continues down-flow by a column. All tests performed at constant pH of 6 and temperature of 27 ° C. The effective variables such as initial concentration، adsorbent bed height and inlet flow rate was studied for removal of cadmium ions. For each trial، value of 6 ml samples was collected at every 30 minutes of the output column. Cadmium ion concentration in each sample was measured with atomic absorption spectrophotometer.
    Results
    Test results showed that the absorption breakthrough curve related to the studied variables. Increasing flow rate and input concentration decreases the saturation point and breakthrough time but increase the depth of adsorbent bed makes it longer. Maximum uptake of cadmium ions was obtained 10. 07mg/g in a flow3ml/min، bed depth 30cm، and initial concentration 30mg/l.
    Conclusion
    According to obtained results، increasing flow rate decreases the maximum of uptake of cadmium ions per gram of absorbent and the absorption efficiency. The input flow 2 ml/min on the adsorbent column with Barley stem was removed cadmium ions as well and also has a large absorption capacity. It is recommended that continuous flow method with the obtained parameters in this study be used in the chemically refining process.
    Keywords: Aqueous solution, Barley stem, Cadmium ion, Continuous flow, Natural sorbent
نکته
  • نتایج بر اساس تاریخ انتشار مرتب شده‌اند.
  • کلیدواژه مورد نظر شما تنها در فیلد کلیدواژگان مقالات جستجو شده‌است. به منظور حذف نتایج غیر مرتبط، جستجو تنها در مقالات مجلاتی انجام شده که با مجله ماخذ هم موضوع هستند.
  • در صورتی که می‌خواهید جستجو را در همه موضوعات و با شرایط دیگر تکرار کنید به صفحه جستجوی پیشرفته مجلات مراجعه کنید.
درخواست پشتیبانی - گزارش اشکال