a. yazdani
-
در مطالعه ی حاضر، پاسخ غیرخطی سیستم های هیسترزیس دوخطی تحت اثر زمین لرزه های سازگار با طیف طرح هدف با به کارگیری روش های خطی سازی آماری معادل مرتبه های دوم و سوم محاسبه شده است. طیف طرح هدف براساس طیف آیین نامه ی لرزه یی ایران در منطقه با لرزه خیزی خیلی زیاد، خاک نوع II و در دو حالت با و بدون آثار حوزه ی نزدیک به گسل در نظر گرفته شده است. طیف پاسخ سیستم های خطی معادل به دست آمده از رویکردهای تیوری ارتعاش های تصادفی و تحلیل تاریخچه ی زمانی در محدوده ی رفتار کشسان با متوسط طیف پاسخ حاصل از تحلیل های تاریخچه ی زمانی غیرخطی مربوط به 250 رکورد مصنوعی سازگار شده با طیف هدف در مقادیر مختلف جابه جایی تسلیم و نسبت صلبیت سیستم مقایسه شده اند. براساس نتایج به دست آمده، انطباق مطلوب نتایج خطی سازی مرتبه ی سوم با نتایج تحلیل تاریخچه ی زمانی غیرخطی، بیانگر کارآمد بودن و دقت مناسب روش در تخمین پاسخ سیستم های غیرخطی تحت تحریک های شدید است.کلید واژگان: ارتعاش های تصادفی، حوزه ی نزدیک گسل، روش خطی سازی، طیف توان، هیسترزیس دوخطیOne of the important issues in performance-based earthquake engineering is the accurate estimation of the response statistics of nonlinear systems under seismic excitation. In this study, the near-field effects contained in the building design regulations against earthquakes (Standard No. 2800, fourth edition) are investigated on the nonlinear response of single degree of freedom systems with bilinear hysteretic restoring force characteristics. Near-field effects are presented in the Standard No. 2800 as spectral correction factor “N” in different seismicity regions. In this study, the site is located in a very high-seismicity zone and the ground type is considered as type II. Second- and third-order linearization methods are used to estimate the response of nonlinear systems. These methods are applied to derive equivalent linear properties. To achieve research goals, it is necessary to represent the input excitation as a quasi-stationary stochastic process compatible with target elastic design spectrum. In this regard, an effective numerical method in the field of random vibrations was used to determine the response spectrum compatible power spectra. After calculating the equivalent parameters related to linearization methods, random vibration theory and time history analysis approaches within the linear range were used to calculate the response of equivalent linear systems. In order to validate the results, the response values obtained from equivalent linearization methods for both approaches were compared with the results of nonlinear time history analysis (NTHA). For this purpose, 250 artificial non-stationary records compatible with two modes of the target spectrum were used to provide reasonable estimates of the peak response of the bilinear hysteretic systems. Artificial records were generated using simulation methods in the field of random vibrations by considering specified envelope functions and power spectral density. According to the results of this study, the second-order linearization method has insufficient accuracy in estimating the response of nonlinear systems under severe excitation. As the natural period of the systems increases, the discrepancy between the results of the equivalent linear system and the results of NTHA increases. Moreover, the good agreement between the third-order linearization results and the results of NTHA indicates the high efficiency of this method in estimating the response of nonlinear systems under the near field excitation.Keywords: random vibration, near-field effect, equivalent linearization method, power spectrum, bilinear hysteretic
-
درنوشتار حاضر، روشی برای شبیه سازی زمین لرزه ی نزدیک گسل شبه پالس با استفاده از مدل سازی مشخصات آنی پیشنهاد شده است. روش پیشنهادی بر اساس فرایند زمان - بسامد است، که برای در نظر گرفتن مشخصات نامانای زمین لرزه ضروری است. در مطالعه ی حاضر، به منظور حفظ مشخصات نامانای زمین لرزه از تبدیلات هیلبرت و موجک مانا استفاده شده است. از تبدیل موجک مانا به منظور تجزیه ی سیگنال زلزله ی اصلی به یک سری زیرباندهای بسامدی و از تبدیل هیلبرت جهت استخراج مشخصات آنی زمین لرزه ها استفاده شده است. به منظور تولید داده های تصادفی جهت شبیه سازی زلزله ها از توزیع ها و توابع مناسب برازش شده روی مشخصات آنی و ضرایب تقریب به دست آمده از آخرین مرحله ی تبدیل موجک مانا استفاده شده است. در مطالعه ی حاضر، از چند زمین لرزه ی پالس دار برای بررسی کارآمد بودن روش پیشنهادی استفاده شده است. نتایج شبیه سازی نشان می دهد روش پیشنهادی به خوبی مشخصات اصلی زلزله ی ثبت شده را در بر می گیرد و همچنین آثار پالس زمین لرزه را نیز به خوبی حفظ می کند.
کلید واژگان: زمین لرزه ی شبه پالس، تبدیل موجک، تبدیل هیلبرت، مشخصات آنی، توزیع گوسینIn areas near active faults, ground motions usually show a large pulse in velocity time history. These near-field pulse-like ground motions increase the structural failure and cause extensive damage to structures. Due to the limited number of pulse-like ground motion recorded in a range of magnitude and distance, there is a small set of possible earthquake scenarios for seismic engineering in a given area, especially in areas near the fault. A new method has been proposed in this paper for simulating near-field pulse-like ground motions using instantaneous feature modeling. The proposed method is introduced based on the time-frequency process which is necessary to consider non-stationary characteristics of ground motion. In this method of simulation, wavelet-based Hilbert transform is used to extract the non-stationary characteristics of original pulse-like ground motion. The stationary wavelet transform is first applied to decompose the original ground motion into a series of subband frequency, and then the instantaneous features are obtained by applying Hilbert transform on each subband frequency. Instantaneous frequencies are modeled by Gaussian distribution and the instantaneous amplitude fitted by Gaussian curves. Approximation coefficients obtained from the last level of wavelet transform are also simulated using the Gaussian curves. Pulse-like ground motion will be simulated using Hilbert and Wavelet inverse transforms and the new generated data for the instantaneous characteristics and approximation coefficients. In this study, four pulse-like ground motions of Imperial Valley1979 and Northridge 1994 were used to verify the effectiveness of this simulation method. Simulated ground motions were compared with the recorded pulse-like ground motions and various criteria were used to confirm the effectiveness of the proposed method. Peak ground acceleration, response spectrums, and arias curves which are important parameters of ground motion were used in this paper to validate the proposed method. Simulation results not only captured the main characteristics of the recorded pulse-like ground motion, but also preserved the effects of the pulse as well.
Keywords: Pulse-like ground motion, wavelet transform, Hilbert Transform, Instantaneous Frequency, Instantaneous Amplitude, Gaussian distribution -
در مقاله پیش رو، روش تف جوشی پلاسمای جرقه ای برای تولید کامپوزیت سه تایی Ti-Al2O3-HA استفاده شد. بدین منظور پودرها تحت فشار MPa 40 در دماهای 1200 و 1300 درجه سانتی گراد به مدت 5 دقیقه سینترشدند. مشخصات میکروساختاری با کمک میکروسکوپ الکترونی روبشی بررسی شد. به منظور بررسی خواص نمونه ها آزمون های سنجش دانسیته، سختی، امپدانس الکتروشیمیایی و پلاریزاسیون انجام شد. نتایج نشان داد که با افزایش دمای تف جوشی ازºC 1200 به ºC 1300 در ساخت کامپوزیت Ti-Al2O3-HA، با توجه به بهبود سینترینگ، دانسیته نمونه ها افزایش و تخلخل ظاهری کاهش می یابد. از طرفی با افزایش دما، سختی نمونه ها از HV 528 به HV 612 افزایش یافت. نتایج آزمون امپدانس الکتروشیمیایی نشان داد با افزایش دمای سینترینگ مقاومت پلاریزاسیونی نمونه از Ωcm2 222 به Ωcm2 996 بهبود یافته است. علاوه بر این دانسیته جریان خوردگی بر اساس آزمون پلاریزاسیون الکتروشیمیایی از μA/cm2 35/16 به μA/cm2 47/1 تقلیل پیدا کرد. بهبود مقاومت به خوردگی به کاهش تخلخل و تشکیل فیلم پسیو مقاوم تر روی سطح نمونه با افزایش دمای سینترینگ نسبت داده شد.
کلید واژگان: تف جوشی پلاسمای جرقه ای، کامپوزیت تیتانیوم آلومینا هیدروکسی آپاتیت، امپداس الکتروشیمیایی، پلاریزاسیون الکتروشیمیاییIn the present study, spark plasma sintering (SPS) technique was used to fabricate Ti-Al2O3-HA composite. Powders were sintered at 40 MPa pressure for 5 min at 1200 and 13000C. Microstructural characterisation was carried out using scanning electron microscopy (SEM). Density, hardness, electrochemical impedance and polarization test were performed to evaluate the properties of the samples. The results showed that by increasing the sintering temperature from 1200 to 1300 0C the density of the samples increases and the apparent prosity decreases. Also with increasing temperature the hardness of the samples increased from 528HV to 612HV. The result of electrochemical impedance test showed the polarization resistance of the sample enhanced from 222 Ωcm2 to 996 Ωcm2 . Furthermore, according to polarization measurements, the corrosion current density was reduced from 16.35 μA/cm2 to 1.47 μA/cm2 . The improvement in the corrosion resistance was attributed to the reduction of prosity and the formation of stronger passive film on the sample surface with increasing sintering temperature.
Keywords: Spark Plasma Sintering, Ti-Al2O3-HA Composite, Electrochemical Impedance Spectroscopy, Electrochemical Polarization -
بار باد از جمله بارهای با عدم قطعیت زیاد و وابسته به موقعیت ساختگاه می باشد. بنابراین ضروری است که در تدوین و تنظیم آیین نامه ها، شرایط اقلیمی و پارامترهای آماری مربوط به مناطق مختلف به صورت جداگانه مورد بررسی قرار گیرند. در این پژوهش بر اساس یک مطالعه پارامتریک به ارزیابی سطح قابلیت اعتماد ترکیب های بار باد در مبحث ششم (ویرایش 1392) پرداخته شده است. برای دستیابی به این امر، پارامترهای آماری بار باد برای نواحی مختلف ایران بررسی گردید و سپس شاخص قابلیت اعتماد تیرهای فولادی در مود خمشی برای آن نواحی محاسبه و با مقدار شاخص قابلیت اعتماد هدف مقایسه شده است. نتایج نشان می دهند که شاخص قابلیت اعتماد در مبحث ششم نسبت به شاخص قابلیت اعتماد هدف، پایین تر است. یکی از دلایل پایین بودن شاخص قابلیت اطمینان تا حد زیادی ناشی از تخمین دست پایین سرعت مبنای باد نسبت به مقدار تجربی آن می باشد.
کلید واژگان: تحلیل قابلیت اعتماد، آیین نامه بارگذاری ایران، ترکیبات بار، پارامترهای آماری، بار بادThe new generation of design codes is established by reliability-based calibration methods. The overall aims of these methods are to achieve consistent levels of safety or structural reliability under different type of uncertainties. According to these methods, the acceptable reliability level of structures is obtained based on statistical descriptions of loads and resistance and also consideration of different types of uncertainties such as the physical uncertainty, the statistical uncertainty and the model uncertainty. In the last decades, based on reliability-based calibration approaches, load and resistance factor design (LRFD) method has been developed for steel buildings design. In this method desired level of safety is obtained by a set of partial load and resistance factor.
The design load combinations for steel structures in Iranian National Building Code (INBC), Part 6, are generally based on other codes such as ASCE/SEI 7-10 standard and National Building Code of Canada (for wind load factors), while the effect of Iranian statistical data for load and resistance has not been considered. In comparison to other loads, such as gravity loads, wind load has a high degree of uncertainty and also it is completely site dependent. Therefore it is important to estimate a suitable statistical model for wind load and also investigate the reliability level of structures subjected to wind load combinations. This paper is a parametric study to assessment the reliability level of wind load combinations for steel beams based on INBC. For this purpose, wind load statistical data are provided for whole of Iran by the climatology data of wind speeds. Based on the FOSM method explicit formulation for reliability index of beams is calculated. The reliability indices for a range of practical load ratios are obtained and compared to the target reliability index. The results indicated that reliability level of wind load combinations in INBC is lower than target reliability index. One of the main reasons for the low level of reliability index for wind load combinations is related to underestimation of reference speed. The results show that by considering the reference speeds based on statistical data, reliability index approaches to target reliability index.Keywords: Reliability analysis, Iranian National Building Code, load combinations, Wind Load, statistical parameters -
In this study, barium aluminosilicate glass sealant was synthesizedand characterized for Solid Oxide Fuel Cell (SOFC) applications. First, the stoichiometric amounts of powder were mixed and melted at 1330°C for 2h, followed by quenching in water. They were then pressed into cylindrical specimens under load of 200 MPa, followed by sintering at different temperatures. The phase content and microstructure of the samples were analyzed by X-ray Diffraction (XRD) and Scanning Electron Microscope (SEM) methods, respectively. Microhardness and toughness of the sintered samples were investigated by means of Vickers micro-hardness test. Young’s modulus and nano-hardness of the glass sealant were measured by nano-indentation method. The thermal expansion coefficient of the specimens was estimated by a dilatometer. The results showed that after sintering at 750°C, sealants with homogeneous microstructure and high density were obtained. The sealants were characterized by mechanical and thermal properties appropriate for SOFC applications with a very low leak rate.Keywords: Barium aluminosilicate, Glass Sealant, Solid oxide fuel cells, Mechanical properties
-
تئوری قابلیت اعتماد، نقشی اساسی در ضوابط طراحی سازه ها ایفا می کند و تحلیل و طراحی سازه ها بر مبنای نظریه ی قابلیت اعتماد، که شاخه یی از تئوری عمومی احتمالات است، در سال های اخیر توجه بسیاری را به خود جلب کرده است. علت این توجه، توانایی در مدل کردن عدم قطعیت در پارامترهای بارگذاری و سازه یی از قبیل مشخصات مصالح، ابعادهندسی، و تحلیل غیرخطی سازه هاست. در این نوشتار، برای محاسبه ی شاخص اعتماد سازه ها روشی ارائه شده است که دو نکته ی مهم یعنی ساده بودن و دقت روش در ارزیابی و محاسبه ی شاخص اعتماد سازه ها در نظر گرفته شده است. مقادیر شاخص اعتماد به کمک نتایج حاصل از تحلیل دینامیکی افزایشی و انتخاب ضریب شکل پذیری به عنوان معیار غیرخطی سازه محاسبه می شود. براساس فرمول بندی ارائه شده، مقدار شاخص اعتماد به عنوان نمونه در سازه های فولادی قاب خمشی طراحی شده براساس آیین نامه ی فولاد ایران مورد ارزیابی قرار گرفته است.
کلید واژگان: شاخص اعتماد، تحلیل دینامیکی افزایشی، شکل پذیری، سازه های قاب خمشی فولادیReliability theory, which itself is a part of general probabilistic concepts, plays a basic role in the design provisions of structures. In limit state or performance-based design, the structural reliability theory plays an essential role in setting the design criteria, as well as demonstrating the target reliability level appropriate to each society. Structural reliability is necessary for having a model that makes it possible to perform rational calculations in the presence of uncertainties in the various parameters encountered in loading parameters and those of structures such as material property, geometric dimensions and the nonlinear dynamic analysis procedure. Although several procedures for structural reliability evaluation, treating non-linear displacement responses, have been proposed, they require complex procedures that may not be used in the practical design process. In the present study, a ductility-based procedure is proposed to maintain both accuracy and simplicity, based on non-linear dynamic response analysis. The use of results of the nonlinear dynamic analysis for a few records to establish the seismic demand curve could be considered the computationally intensive part of the incremental dynamic analysis (IDA). The IDA is an emerging structural analysis method that offers thorough seismic demand and limit-state capacity prediction capability by using a series of nonlinear dynamic analyses under a suite of multiply scaled ground motion records. We used probabilistic tools, by applying the total probability theorem, in order to derive the hazard values for the ductility-based response. This study presents an analytical foundation for probability-based formats for seismic design and assessment of structures. In this study, a reliability assessment of six steel moment resisting frames (MRF), designed according to Iranian codes, is carried out. The reliability indices of these designed steel MRF structures are to be estimated using the present procedure, the ductility-based procedure.
Keywords: Reliability Index, Incremental Dynamic Analysis, Ductility, MRF Steel Structures -
به منظور بررسی تاثیر روش های کاشت و مقادیر بذر مصرفی بر ویژگی های رشد و عملکرد یونجه رقم همدانی(Medicago sativa L.)، آزمایشی در سال 88 - 1387 در مزرعه تحقیقاتی دانشکده کشاورزی دانشگاه شیراز (باجگاه) اجرا شد. آزمایش به صورت فاکتوریل در قالب طرح بلوک های کامل تصادفی با 4 تکرار بود. فاکتورهای مورد مطالعه روش های کاشت (جوی و پشته ای، کرتی ردیفی، کرتی درهم و بستر تخت) و مقادیر بذر یونجه (5، 10، 15 و 20 کیلوگرم بذر در هکتار) بود. اثر روش های کاشت و مقادیر بذر بر وزن خشک علوفه معنی دار (05/0p <) شد. بیشترین وزن خشک علوفه در چین اول (84/6 تن در هکتار) و سوم (45/7 تن در هکتار) در تیمار کاشت جوی و پشته ای و مقدار 20 کیلوگرم در هکتار و کمترین وزن خشک علوفه در چین اول (63/3 تن در هکتار) در کاشت به صورت بستر تخت و میزان 5 کیلوگرم بذر در هکتار و در چین سوم علوفه (03/4 تن در هکتار) در کاشت کرتی درهم و میزان 10 کیلوگرم بذر در هکتار به دست آمد. نتایج نشان داد مقادیر مختلف بذر یونجه بر تعداد علف های هرز رشد یافته در مزرعه تاثیر معنی دار داشته (05/0 p <) و بیشترین تعداد علف های هرز در مقدار 5 کیلوگرم بذر یونجه در هکتار و کمترین تعداد بوته های علف های هرز در مقدار 20 کیلوگرم بذر یونجه در هکتار به دست آمد.
کلید واژگان: یونجه، مقدار بذر، عملکرد علوفه، علف هرزIn order to evaluate the effects of planting methods and seeding rates on growth characteristics and yield of alfalfa (Medicago sativa L.)، Hamedani cultivar، a field experiment was conducted in 2008 at College of Agriculture، Shiraz University، Iran. The experimental design was a completely randomized block with four replicates in a factorial arrangement of the treatments. The factors consisted of planting methods (furrow planting، broadcasting، row planting، and flat bed planting) and alfalfa seeding rates (5، 10، 15، and 20 kg seed ha-1). Results showed that planting methods and seeding rates had a significant effect on forage dry matter so that the highest forage yield in the first and third cuttings was obtained in furrow planting method and 20 kg seed ha-1 and the lowest forage dry weight in the first and third cuttings were obtained in flat bed planting method and 5 kg seed ha-1 and broadcasting method and 10 kg seed ha-1، respectively. Seeding rates also had a significant effect on number of weeds so that maximum and minimum weed numbers were obtained in 20 kg and 5 kg seed ha-1. Our results showed that 20 kg seed ha-1 and furrow planting method was the best treatment to gain maximum forage yield and minimum weed''s detrimental impact.
Keywords: Alfalfa, Seeding rate, Forage yield, Weed -
In this paper, we solve a linear system of second-order boundary value problems by using the quadratic B-spline nite el- ement method (FEM). The performance of the method is tested on one model problem. Comparisons are made with both the analyti- cal solution and some recent results.The obtained numerical results show that the method is ecient.Keywords: Finite element method, Quadratic B-splines, Bound-ary Value Problems
-
آب، راز ماندگاری جهان و از عناصر اصلی بقا و دوام چرخش زندگی در کره زمین است . بدون تردید کشورایران همانند دیگر کشورهای خاورمیانه در سال های پیش رو با بحران جدی ناشی از کمبود آب روبه رو خواهد بود .بنابراین شناخت و معرفی هر چه بیشتر منابع بهینه آب، الگوی درست مصرف و بهره گیری صحیح و مناسب از منابعزیرزمینی و آب های جاری مقوله ای است که سیاست گذاران و برنامه ریزان امور آب با نگرانی و دقت به آنپرداخته اند.ریزش های جوی مهم ترین منبع طبیعی آب برای انواع فعالیت های بشری (صنعتی، کشاورزی و شرب) است.از آن جا که ریزش های جوی با متغیرهای زمانی و مکانی زیادی همراه هستند اطلاعات موجود در خصوص توزیع آبو هوایی و عوامل سینوپتیکی ریزش های جوی بسیار اندک است.در ایران شبکه مشاهدات زمینی به اندازه کافی متراکم نبوده و بسیار پراکنده و نامنظم است . فاصلهایستگاه های مشاهداتی زمینی به خصوص در مناطق کوهستانی (مانند استان فارس) با توجه به عامل توپوگرافی ازچند کیلومتر تا چند صد کیلومتر متفاوت است . بنابراین بررسی باران به روش سنتی که نیاز به شبکه باران سنجیمتراکم دارد هم از لحاظ اجرایی و هم از لحاظ اقتصادی امکا نپذیر و مقرون به صرفه نمی باشد. در مقاله حاضر به منظور تخمین بارندگی روزانه استان فارس از دو روش درون یابی کریجینگ (Kriging) و معکوس وزنی فاصله (IDW) استفاده گردید . سپس دقت نتایج حاصل از اجرای مدل ها از طریق تست آماری RMSE مورد ارزیابی قرار گرفت . نتایج حاصل از اجرای مدل و ارزیابی دقت آن ها نشان داد که روش کریجینگ نسبت به روش IDW از دقت بیشتری برخوردار می باشد . همچنین نتایج نشان داد که در بین روش های کریجینگ، روش معمولی دایره ای و نمایی از کم ترین خطا نسبت به سایر رو شهای کریجینگ برخوردار می باشند.
کلید واژگان: درونیابی، کریجینگ، درونیابی عکس فاصله، بارندگی روزانه GISEvaluation of different interpolation methods on dailyrainfall estimation, Case study: Fars ProvinceTerritory, Volume:4 Issue: 13, 2007, PP 54 -68Rainfall is one of the most important natural sources of water used by mankind foragricultural and industrial applications. Because of the difficulty of rainfall monitoring,which has high spatial and temporal variability, our knowledge of both the its synopticand climatological distribution over most of the country is not well known.Climatological investigations in Iran lack adequate meteorological observations tounderstand and interpret diverse climatic features. In the country as a whole, theground observation network is not dense enough to provide the detailed informationrequired, especially in rugged regions. Combined with this is the problem of pooraccessibility to the mountainous regions, which has resulted in the areal distribution ofrainfall being poorly known. In addition, the data collected by the existingmeteorological stations, with a few exceptions, are mostly discontinuous, nonhomogenousand short period observations. Such limited data sets, make it difficult toboth accurately delimit different climatic regimes across the country and identifysignificant departures from normal conditions, whereas many climatologicalapplications and investigations should ideally be based on the data collected at givenpoints over long periods and should have a good spatial and temporal coverage.Perhaps the most urgent problem facing rainfall measurement at the present time isdata collection - one of the most costly areas in meteorology and hydrology.In this paper, the central aim is to investigate the potential of GeographicalInformation System for monitoring Fars province’s rainfall with special reference toKriging and IDW (Inverse Distance Weighting), to describe pre-processingapproaches, including relative calibration, and to examine various techniques for bothrainfall monitoring.Analyses of the GIS techniques provided very useful information on both thespatial and temporal distributions of rainfall over regional space, although datacollected by Kriging technique showed more accurate than IDW technique. In order toexplore the appropriate method, the accuracy of the obtained results from differentmethods using RMS was examined. The results showed that among different usedkriging methods, the circular and exponential ordinary had lowest error.
Keywords: Interpolation, Kriging, IDW, daily rainfall, GIS
- در این صفحه نام مورد نظر در اسامی نویسندگان مقالات جستجو میشود. ممکن است نتایج شامل مطالب نویسندگان هم نام و حتی در رشتههای مختلف باشد.
- همه مقالات ترجمه فارسی یا انگلیسی ندارند پس ممکن است مقالاتی باشند که نام نویسنده مورد نظر شما به صورت معادل فارسی یا انگلیسی آن درج شده باشد. در صفحه جستجوی پیشرفته میتوانید همزمان نام فارسی و انگلیسی نویسنده را درج نمایید.
- در صورتی که میخواهید جستجو را با شرایط متفاوت تکرار کنید به صفحه جستجوی پیشرفته مطالب نشریات مراجعه کنید.