به جمع مشترکان مگیران بپیوندید!

تنها با پرداخت 70 هزارتومان حق اشتراک سالانه به متن مقالات دسترسی داشته باشید و 100 مقاله را بدون هزینه دیگری دریافت کنید.

برای پرداخت حق اشتراک اگر عضو هستید وارد شوید در غیر این صورت حساب کاربری جدید ایجاد کنید

عضویت
جستجوی مقالات مرتبط با کلیدواژه

finite element method

در نشریات گروه صنایع چوب و کاغذ
تکرار جستجوی کلیدواژه finite element method در نشریات گروه کشاورزی
تکرار جستجوی کلیدواژه finite element method در مقالات مجلات علمی
  • اکبر رستم پور هفتخوانی*، آرش چاوشی، محمد عربی
    در این تحقیق، خواص خمشی پروفیل های تولیدی شرکت چوب پلاست عصر هنر اندازه گیری و سپس با هدف کاهش هزینه و زمان اندازه گیری دقت روش اجزای محدود با نرم افزار ANSYS برای پیش بینی آنها ارزیابی شد. از اینرو، ابتدا خواص خمشی نمونه های کوچک شاهد با طول دهانه 180 میلیمتر انجام شد. مدول الاستیسیته خمشی نمونه های کوچک و ضریب پوآسون 3/0به عنوان داده ورودی برای پیش بینی استفاده شد. سپس چهار نوع پروفیل توخالی و توپر با طول دهانه 180 و 450 میلیمتر تحت بارگذاری خمش سه نقطه-ای با دستگاه 0308 Hounsfield با سرعت بارگذاری mm/min 5 آزمایش شدند. بنابراین، مقادیر تنش و خیز آنها اندازه گیری و با نتایج روش اجزای محدود (FEM) مقایسه شدند. نتایج جدول تجزیه واریانس نشان داد که تاثیر مستقل نوع پروفیل بر MOR معنی دار است. همچنین نتایج نشان داد که تاثیر مستقل و متقابل طول دهانه و نوع پروفیل بر MOE از نظر آماری معنی دار است. نتایج تاثیر مستقل نشان داد که با افزایش طول دهانه از 180 به 450 میلیمتر، مقدار MOR و MOE به ترتیب %8/8 کاهش و %7/17 افزایش، و با تغییر نوع پروفیل مقدار MOR و MOE به ترتیب %1/33 و %2/24 تغییر کردند. نتایج تاثیر متقابل نشان داد که با تغییر همزمان طول دهانه و نوع پروفیل مقادیر MOR حدود 9/43 درصد و مقدار MOE 6/66 درصد تغییر کرد. نتایج نشان داد که روش اجزای محدود مقدار MOR را با میانگین درصد خطای مطلق (MAPE) کمتر از %03/3 و خیز متناظر آنها را با MAPE کمتر از %25/15 پیش بینی کرد. با توجه به خطای رضایتبخش این روش می توان روش اجزای محدود را به عنوان روشی کارآمد برای پیش بینی خواص مکانیکی این محصولات پیشنهاد کرد.
    کلید واژگان: پروفیل چوب پلاستیک، پیش بینی، خیز، روش اجزای محدود، مقاومت خمشی
    Akbar Rostampour Haftkhani *, Arash Chavooshi, Mohammad Arabi
    In this study, bending performance of the WPC profiles of Asre Honar company were measured, then were predited by finite element method (FEM) with ANSYS software to decrease the cost and time of measurement. Therefore, the bending strength of small control specimens with a span length of 180 mm were firstly measured. Accordingly, their bending modulus of elasticity (MOE) and Poisson's ratio of 0.3 were used as input data for prediction. Therefore, four types of hollow and solid WPC profiles with span lengths of 180 and 450 mm were tested under three-point bending loading with a Hounsfield 0308 testing machine with a loading rate of 5 mm/min. Subsequently, their MOR and creep values were measured and compared with those predicted by the FEM. The results of the analysis of variance (ANOVA) Table showed that the main effect of profile types on MOR was statistically significant. Furthermore, the main and the interaction effects of the span lengths and profile types on MOE were statistically significant. The investigation of the main effects revealed that MOR and MOE decreased by 8.8% and increased by 17.7%, respectively by raising the span length from 180 to 450 mm, and also they altered by 33.1% and 24.2% with the change in profile types. In addition, the interaction effects showed that MOR and MOE values changed by 43.9% and 66.6%, respectively with the simultaneous change of the span lengths and profile types. The results indicated that the FEM predicted the MOR values with a mean absolute percentage error (MAPE) of less than 3.03% and their corresponding creep with a MAPE of less than 15.25%. According to the satisfied MAPE of FEM, it could be suggested as an efficient method for predicting the bending properties of these products.
    Keywords: wood-plastic profile, finite element method, prediction, bending strength, Creep
  • حجت همت آبادی*، مهراب مدهوشی، ابوالقاسم خزائیان، قنبر ابراهیمی
    در این پژوهش مقاومت به خمش و برشی چندسازه ساختمانی با لایه های چوبی متقاطع (CLT) سه لایه ساخته شده از ترکیب گونه پهن برگ صنوبر (Populus deltoides) و راش (Fagus orientalis) با استفاده از روش تجربی بررسی گردید. نمونه های آزمایشگاهی با نسبت های طول به ضخامت 6، 10، 15، 20 و 25 و پهنای 30 سانتیمتر و ضخامت 6 سانتیمتر در هر دو جهت اصلی و فرعی پنل ساخته شدند و مقاومت آنها با استفاده از آزمون خمش سه نقطه ای بر اساس استاندارد 198 ASTM D بررسی شد. همچنین با استفاده از روش اجزای محدود با نرم افزار آباکوس، نمونه های پنل CLT تحت بار خمشی مدل سازی شدند. نتایج نشان داد که با افزایش نسبت طول به ضخامت تیر از 6 تا 25، مقدار میانگین مدول الاستیسیته (MOE) و مقاومت خمشی (MOR) CLTها در هر دو جهت اصلی و فرعی افزایش یافت. بعکس میانگین مقاومت برشی () نمونه ها در هر دو جهت اصلی و فرعی پنل کاهش یافت. نتایج توزیع تنش نمونه ها با روش اجزای محدود نشان داد که مکان و مقدار توزیع تنش های خمشی و برشی هر لایه از پنل در جهت اصلی و فرعی پنل با یکدیگر متفاوت است و در جهت اصلی پنل CLT لایه های سطحی سهم بیشتری در تحمل بار نهایی دارند، اما در جهت فرعی پنل لایه وسط مهمترین نقش را در تحمل بار نهایی ایفا می کند. در این پژوهش نتیجه گیری شد که می توان برای محاسبه مدول الاستیسیته و خمشی CLT از نمونه هایی با نسبت های طول به ضخامت بالاتر از 15 بر اساس استاندارد 198 ASTM D استفاده کرد. به همین دلیل اختلاف کمتر از 10 درصد بین نتایج مدول الاستیسیته حاصل از مدل سازی عددی و نتایج تجربی، مدول الاستیسیته CLT بر اساس  روش اجزای محدود قابل پیش بینی بود.
    کلید واژگان: چوب با لایه های متقاطع، CLT، راش، صنوبر، مقاومت به خمش و برش، اجزای محدود
    Hojat Hematabadi *, Mehrab Madhoushi, Abolghasem Khazaeian, Ghanbar Ebrahimi
    This study investigated the bending and shear strength of hybrid cross-laminated timber (CLT) manufactured from beech (Fagus orientalis) and poplar (Populus deltoides) wood using experimental and finite element methods. The CLT panels were manufactured at various span to depth ratios 6, 10, 15, 20 and 25 with width of 30 cm and thickness of 2 cm in both major and minor directions. Then, the bending and shear strength of CLTs were measured using three-point bending test according to ASTM test methods. The results indicated that with the increase of span to depth ratio of the beam from 6 to 25, the averages modulus of elasticity (MOE) and modulus of rupture (MOR) values were increased in both major and minor directions. On the contrary, the averages shear modulus ( ) values of specimens in both directions were decreased.  Moreover, the results of finite elements showed that the amounts of stress distributions and their locations were different in major and minor directions of the beam. In the major direction, the surface layers were primarily contributed load-carrying capacity of CLT panels, while in the minor direction the middle layer played the most significant role for load-carrying capacity. In this research, it was resulted that specimens with span to depth ratio greater than 15 based on ASTM D198 can be used for calculating MOE and MOR of CLT panels. Furthermore, due to existence of lower difference than 10% between experimental and numerical results, modules of elasticity of CLTs were predictable according to finite element method
    Keywords: Cross laminated timber, beech, Poplar, Bending, shear strength, Finite element method
  • حمیده عبدل زاده *، محمد لایقی، قنبر ابراهیمی، مهدی قاسمیه
    در تحقیق حاضر بررسی آزمایشگاهی و عددی جامعی در رابطه با عملکرد سازه ای اتصالات سربه سر با اعضای چوب-پلیمر (پلی(-فورفوریل الکل)) تحت تنش مرکب در مقایسه با آزمونه های شاهد انجام شد. هدف از این تحقیق افزایش هم زمان عملکرد این اتصالات در فضا ی بیرونی و تحت بارگذاری مرکب بوده است. برای بررسی عملکرد این اتصالات آزمونه هایی با دو مقدار متفاوت فورفوریلاسیون در سطوح ‏20% و 65% در مقایسه با آزمونه های شاهد مورد ارزیابی قرار گرفته اند. خواص مکانیکی فراورده حاصل بر اساس استاندارد ASTM-D143 تعیین و براساس آن ها ویژگی های ماده برای مدل تعیین شد. مقادیر نیرو در حد تناسب تجربی با نتایج مدلFEM مقایسه شد. نتایج به دست آمده از مدل نیز کاملا نتایج تجربی را تایید کرد. اعتبارسنجی نتایج مدل همخوانی بسیار خوبی با نتایج تجربی نشان داد. برای به دست آوردن درک درستی از رفتار اتصال در مدل FEM و پیش بینی علت های شکست آن تحت بار، برخی از خواص مکانیک شکست چوب پلیمر مورد استفاده قرار گرفت.
    کلید واژگان: روش اجزای محدود، اتصال سربه سر، تنش مرکب، فورفوریلاسیون، مکانیک شکست
    Hamideh Abdolzadeh *, Mohammad Layeghi, Ghanbar Ebrahimi, Mahdi Ghassemieh
    In this study, a comprehensive experimental and numerical investigation concerning with structural performance of butted joints constructed with wood-polymer members (poly (furfuryl alcohol)) was carried out under combined stresses in comparison with control specimens. The aim of this research was to enhance performance of these joints in outdoor applications especially under combined stress. For investigation of this joints performance, specimens with two different values of furfurylation at 20% and 65% in comparison with control specimens were evaluated. Mechanical properties of specimens were determined according to ASTM D-143 and materials properties were defined by this properties for modeling. Proportional limit of loading value from experimental was compared with result of FEM model. Result of FEM model completely confirmed experimental results and the validation of model was performed well. To understand about joint behavior at FEM model and to predict the fracture reasons, some properties of fracture mechanics related to wood polymer were used.
    Keywords: finite element method, butted joint, combined stress, furfurylation, fracture mechanics
  • مسیب دالوند *، پیام مرادپور
    در این پژوهش توزیع تنش و کرنش سه بعدی در پین چوبی و خط چسب در اتصال های L شکل ساخته شده از تخته چندلا با پین چوبی مورد بررسی قرار گرفته است. اعضای اتصال از تخته چندلا 19 میلی متر ساخته شده از گونه های پهن برگ (راش، توسکا و ممرز) بودند. در این پژوهش اثر قطر پین چوبی راش ( 6، 8 و 10 میلی متر) و عمق نفوذ ( 9، 13 و 17 میلی متر)، بر ظرفیت لنگر خمشی اتصال ها L شکل زیر بار فشاری به صورت تجربی مورد بررسی قرار گرفت، سپس توزیع تنش و کرنش پین چوبی و خط چسب آزمونه ها به روش اجزای محدود و با استفاده از نرم افزار ANSYS شبیه سازی شدند. نتایج نشان دادند که ظرفیت لنگر خمشی با افزایش قطر پین از 6 به 8 میلی متر روند افزایشی داشته است، ولی با افزایش پین از 8 به 10 میلی متر روند نزولی مشاهده شده است. ظرفیت لنگر خمشی با افزایش عمق نفوذ افزایش یافت. نتایج تحلیل عناصر محدود نشان دادند که با افزایش قطر پین میزان تنش و کرنش در پین و خط چسب افزایش می یابد و این افزایش تنش در اتصال های ساخته شده با پین به قطر 10 میلی متر باعث شکست اعضای اتصال و در نتیجه کاهش مقاومت اتصال شده است. همچنین بر اساس نتایج به دست آمده از تحلیل مدل، بیشترین تنش در پین و خط چسب، در محل اتصال بین اعضای اتصال به وجود آمده است.
    کلید واژگان: تنش، کرنش، پین چوبی، اتصال L شکل، روش اجزای محدود
    Mossayeb Dalvand *, Payam Moradpour
    In this study 3D stress-strain distribution of dowel and glue line on L-type joints made of plywood doweled was investigated. Members of joints made of 11-ply hardwood plywood (Hornbeam, Beech and Alder) that were 19 mm in thickness. In this study effect of beech dowels in three levels diameters (6, 8 and 10 mm) and penetration of depth (9, 13 and 17 mm) on bending moment capacity of L-type joints under compression loading was investigated as experimental test, then stress-strain distribution of wood dowel and glue line in specimens were simulated by means of ANSYS 15 software with finite element method (FEM).Results have shown that bending moment resistance increased with increasing dowel diameter from 6 to 8 mm, but downward trend was observed with increasing 8 to 10 mm in dowel diameter. Bending moment resistance increased with increasing penetration depth. Also, result obtained of simulation by means of ANSYS software have shown that stress-strain in dowel and glue line increased with increasing diameter of dowel and Increasing stress in joints made of diameter dowel 10 mm due to fracture in joints and decrease in resistance once. According to results obtained of model analysis, the ultimate stress of dowel and glue line occurred in the area that joints were contacted.
    Keywords: Stress, Strain, Wood dowel, L-type joints, Finite element method
  • اخسان کتابی، امیر لشگری*
    هدف در این تحقیق بررسی تاثیر ساختار سازه خرپا بر سفتی و توزیع تنش در عضوهای سازه خرپا است. به این منظور نمونه هایی در 11 ساختار و چهار4 تکرارکه در مجموع 44 نمونه خرپا با چوب صنوبر_تبریزی ساخته و همزمان از دو اتصال مفصلی توسط چسب چوب و اتصال اصطکاکی توسط میخ استفاده شد. برای محاسبه مقاومت خرپاها ابتدا سازه ها توسط دستگاه آزمون مکانیکی با سرعت 12/5 میلیمتر بر ثانیه و 3/5 کیلونیوتن بارگذاری و نتایج آزمون مکانیکی نشان داد، خرپای هیپگیردر بیشترین مقاومت، کمترین توزیع تنش را دارا بوده و تاثیر ساختار خرپا بر روی مقاومت و توزیع تنش در عضوهای آن در سطح 95% معنی دار است. برای نشان دادن توزیع تنش بر روی عضوها از روش اجزاء محدود و نرم افزارهای مدل سازی، اتوکد و کتیا و نرم افزار انسیس جهت تحلیلی عناصر محدود استفاده و نتایج حاکی از آن است که تمرکز تنش حداکثر، در تعامل با شکست در حالت تجربی می باشد.
    کلید واژگان: خرپا، آزمون مکانیکی، اتصال مفصلی، اتصال اصطحکاکی، روش عناصرمحدود
    Ehsan Ketabi, Amir Lashgari *
    In this study was to evaluate the impact of the truss structure on stiffness and stress distribution in the truss structural members. Made and synchronizes this structures with any Populus_ Nigra lumbers, in finally made 44 truss structure with 11 varying samples and 4 replicates. were used by two joint like friction joints was created with Glue stick and dual joint was created with nails to the 4.5 cm and calculate the resistance trusses structures by mechanical testing machine with 12.5 mm/min loading speed and 3.5 KN than mechanical test results showed, Hip Girder truss most resistance stress distribution and were the least impact on the strength and distribution of tension truss structure is significant in 95%. To show the stress distribution on the members, modeling software was AutoCAD, Catia and finite element analysis software was ANSYS. In finally the results show that maximum stress concentration, failure to engage in experimental mode.
    Keywords: truss, mechanical test, dowel joint, Wood, friction joint, finite element method
  • سهیلا زمانی نسب، امیر لشگری*، آژنگ تاج دینی
    در این تحقیق مقاومت و تمرکز تنش بر روی سازه ی صندلی با تغییر نوع اتصال(اتصال کام و زبانه- اتصال دوبل) مورد بررسی قرار گرفت.برای ساخت صندلی ها از چوب چنار(platanus orientalis) استفاده و برای محاسبه ی مقاومت صندلی ها از دستگاه آزمون مکانیکی با سرعت بارگذاری 7/12 میلی متر بر دقیقه و برای نشان دادن توزیع تنش بر روی عضوهای صندلی از نرم افزار Ansys استفاده شد.نتایج نشان می دهد که صندلی با اتصال زبانه و کام و ساختاری ساده و با قید دارای مقاومت بیشتر و توزیع تنش کمتری نسبت به صندلی با اتصال دوبل با ساختار ساده و با قید بوده و تاثیر نوع اتصال روی مقاومت صندلی معنی دار بود.توزیع تنش نشان می دهد که تنش حداکثر بر روی اتصالات افقی صندلی قابل مشاهده می باشد.مدل های عناصر محدود نشان می دهند که توزیع تنش در صندلی های با اتصال زبانه و کام یکنواخت تر می باشد
    کلید واژگان: اتصال دوبل، نرم افزار انسیس، توزیع تنش، عناصر محدود
    Soheila Zamaninasab, Amir Lashgari *, Azhang Tajdini
    In this research, resistance and stress concentration on the seat structure were examined by changing the type of connection (tongue and groove connection , and double connection). platanus orientalis used to make wooden chairs. Moreover, we applied Ansys to calculate resistance and mechanical testing machine with a load of chairs 7/12 mm per minute to show the stress distribution on the chairs members . The results show that chairs by tongue and groove connection and having a simple structure and with bail , have more resistance and less stress distribution than a double chair with a simple structure and with indicating connection and the impact of the type of connection were significant on the chair resistance . The stress distribution shows that the maximum stress concentrations on the horizontal joints are visible . Finite element models show that the stress distribution is more uniform in chairs with tongue and groove connections.
    Keywords: dowel joint, Ansys software, finite element method, stress distribution
نکته
  • نتایج بر اساس تاریخ انتشار مرتب شده‌اند.
  • کلیدواژه مورد نظر شما تنها در فیلد کلیدواژگان مقالات جستجو شده‌است. به منظور حذف نتایج غیر مرتبط، جستجو تنها در مقالات مجلاتی انجام شده که با مجله ماخذ هم موضوع هستند.
  • در صورتی که می‌خواهید جستجو را در همه موضوعات و با شرایط دیگر تکرار کنید به صفحه جستجوی پیشرفته مجلات مراجعه کنید.
درخواست پشتیبانی - گزارش اشکال