Optimization of length and diameter of laterals in rain hose irrigation system
Author(s):
Message:
Article Type:
Research/Original Article (بدون رتبه معتبر)
Abstract:
Introduction
Meeting the food and fibre demands of a growing global population is a considerable challenge. To date, irrigated agriculture has been responsible for 40% of the total food and fibre production whilst using only 18% of world’s arable land, Irrigation requirements, however, account for nearly 70% of the world’s total freshwater withdrawals and have significantly altered hydrological and environmental conditions in both surface and subsurface water resources. This has generated criticism and debate about the (un) sustainability of irrigated agriculture. Irrigation managers must often justify the use, efficiency and productivity of water in competition and comparison with other uses and users. The challenge is to enhance water allocation decisions to reduce negative environmental impacts, whilst continuing to satisfy food and fibre demands. Research and investments have been oriented towards applying cost effective technology, precision agriculture, and environmentally friendly techniques to pursue sustainable water use in agricultural development. Rain Hose is affordable spray irrigation technology. Its replacement for Sprinkler Irrigation System. It's easy to install and maintain. Rain Hose is flexible hose with pattern of drip holes. These drip holes are made with nano punching technology to ensure uniform flow of water. Rain Hose is suitable for closely spaced crops, onion, vegetable crops, leafy vegetables, groundnut etc. Rain Hose is an affordable spray irrigation technology. It is a replacement for the sprinkler irrigation system. It is easy to install and maintain. Rain Hose is a flexible hose with a pattern of drip holes. These drip holes can be made with nano punching technology to ensure a uniform flow of water. The rain hose is suitable for closely spaced crops like onions, vegetable crops, leafy vegetables, groundnuts, etc. Rain hose is an emerging irrigation technique which is widely used for closed spaced crops. It is an alternative to the sprinkler irrigation but both are adopting the spraying technology. The spraying pattern in the rain hose irrigation will be linear on either sides up to the full stretch of the rain hose. Variation in the spray width and the discharge of water from the nozzles of rain hose under different flow rates are studied for various available diameters of rain hose. There is no standard available on the optimum combination of length and diameter of rain hose. A Catch-can method based field test was conducted to estimate the influence of length and diameter of rain hose for four flow rates and the pressure values through the main pipe viz., were noted down.
Materials and Methods
A rain hose of five diameters 20mm, 32mm, 40mm, 50mm, and 63mm were attached to the main pipe individually using proper setup and the spray width and discharge through the nozzles were measured for every 20m interval. The 2end coupler is connected with the main pipe and the other end is sealed shut, making sure that the water flows through the main hose in the desired pressure. The rain hose is attached laterally to a main PVC pipe of 63mm diameter, where the connection is made by the help of 4-way couples. The end of the rain hose is closed with an end cap. A 5HP open-well motor of type TMH4H is used, wherein the discharge capacity is 33, 120 litres per hour. Regulating valves and Reducers are used to control the flow of water in the system. The standard wall thickness of all the above used rain hoses are 350 microns. The field test conducted, is conducted at an interval of 20m from the main pipe where the total discharge of the water and the width of spraying in between the interval points are obtained for the rain hoses of the above mentioned diameters, as a result of which the effective laying length of the rain hose is evaluated by considering the reduction in water discharge and spraying width, in each types.
Results
For every 20m intervals, the corresponding spraying width and the water discharge in between the intervals for various diameter rain hose are graphically represented. The results of this study can be of great help to researchers in the purposeful application of precipitation-runoff and timely management of water resources.
Conclusions
These results are obtained in Coimbatore. There will be chances of slight deviation in the results based on other environmental condition. There will be a maximum possibilities of water leakage if joints are increased and it has to meet the pressure fluctuations throughout the length of the rain hose.
Language:
English
Published:
Water Productivity Journal, Volume:2 Issue: 3, Summer 2022
Pages:
37 to 44
magiran.com/p2546889  
دانلود و مطالعه متن این مقاله با یکی از روشهای زیر امکان پذیر است:
اشتراک شخصی
با عضویت و پرداخت آنلاین حق اشتراک یک‌ساله به مبلغ 990,000ريال می‌توانید 70 عنوان مطلب دانلود کنید!
اشتراک سازمانی
به کتابخانه دانشگاه یا محل کار خود پیشنهاد کنید تا اشتراک سازمانی این پایگاه را برای دسترسی نامحدود همه کاربران به متن مطالب تهیه نمایند!
توجه!
  • حق عضویت دریافتی صرف حمایت از نشریات عضو و نگهداری، تکمیل و توسعه مگیران می‌شود.
  • پرداخت حق اشتراک و دانلود مقالات اجازه بازنشر آن در سایر رسانه‌های چاپی و دیجیتال را به کاربر نمی‌دهد.
In order to view content subscription is required

Personal subscription
Subscribe magiran.com for 50 € euros via PayPal and download 70 articles during a year.
Organization subscription
Please contact us to subscribe your university or library for unlimited access!