Investigating Physical and Mechanical Properties of Bionanocomposite Film Based on Flaxseed Mucilage and Cellulose Nanocrystal

 Manufacturers are trying to replace plastic materials in the food packaging industry with biodegradable and edible films. Biodegradable edible films and coatings are mainly made from carbohydrates, lipids and proteins and their mixtures. In recent decades, various carbohydrates from plant sources have been investigated and introduced as new compounds for the preparation of these films. Flaxseed gum is a white to cream-colored powder that dissolves in water and produces a gel, and is a desirable compound for forming films and coatings. Recently, through the integration of reinforcements or fillers with at least one nanometer dimension in the substrate of one or more natural biopolymers, the physicochemical, mechanical, optical, thermal and barrier properties of pure biofilms have been improved. The use of cellulose nanoparticles in biofilms as a reinforcing agent for polymer materials leads to the creation of composite films with better quality characteristics and leads to the creation of functionalization activities in film production. Therefore, the aim of this research was to produce and characterize edible and biodegradable film based on the combination of flaxseed gum and cellulose nanocrystals.

 Cellulose nanocrystals (Degree of crystallinity: 42% and average particle size: 58 nm) were extracted from cotton linters. Glycerol and other chemicals used for this research were obtained from Merck, Germany. Flaxseeds were purchased from the local market of Shiraz (Iran). Bionanocomposite films were prepared from different ratios (0:100, 30:70, 50:50, 70:30 and 100:0) of flaxseed mucilage (2% w/v) and cellulose nanocrystal (6% w/v) solutions. The prepared solutions were poured on a petri dish with a diameter of 15 cm and dried in an oven at 80°C for 4 hours. Their physical, color and mechanical properties were investigated and the best ratio was selected for the preparation of bionanocomposite film. The produced films were subjected to different analysis to determine thickness, solubility, water absorption capacity, permeability to water vapor, tensile strength, elongation at break point, and colorimetry. The microstructure of the produced film was studied using a scanning electron microscopy (SEM).The average data were analyzed by analysis of variance in a completely randomized design using SPSS 22.0 software. Differences between treatments were expressed in Duncan's multiple range test at the 95% probability level (p<0.05) and the corresponding graphs were drawn with Excel 2013.

 The results of the film thickness test showed that the film containing 100% mucilage has the lowest thickness and with the addition of cellulose nanocrystals, the thickness increased significantly (p<0.05). The results of the water solubility and water absorption capacity of the film samples showed that the addition of cellulose nanocrystals to the flaxseed mucilage film initially led to a significant decrease in the water solubility and water absorption capacity (p<0.05), so that the lowest level ofthese two physical parameters were obtained in the film containing the combination of 70% flaxseed mucilage and 30% cellulose nanocrystal, and then with the increase of cellulose nanocrystals, an increase in water solubility and water absorption capacity of the films was observed. Nanocrystal cellulose at low levels (30%) acted as a filler and was uniformly dispersed in the network of the film and by filling the empty pores of the biopolymer film based on flaxseed mucilage, it caused the transfer of water vapor more complicated and reduced the permeability to water vapor. However, its higher amount increased the permeability of the film to water vapor.The results showed that by adding cellulose nanocrystal to the film based on flaxseed mucilage and increasing its amount, the brightness of the films decreased and the intensity of redness, yellowness and turbidity of the films increased significantly (p<0.05). By combining flaxseed mucilage and cellulose nanocrystals in a ratio of 30:70, the best film was produced in terms of mechanical strength and stability against moisture and water vapor. The SEM image of this film showed a smooth, even surface and a uniform distribution of cellulose nanocrystals in the film network.

 The results finally showed that the combination of flaxseed mucilage and cellulose nanocrystals in a ratio of 30:70 was able to produce a biodegradable and edible film with favorable structural and barrier properties. The characteristics of this film include; thickness (0.313mm), solubility (53.42%), water absorption capacity (44.44%), permeability to water vapor (0.350 g.m-1s-1Pa-1 × 10 -10), tensile strength (0.973 MPa), elongation at break point (30.52%) were obtained. The colorimetric indices L*, a*, b* and turbidity were determined as 79.73, 1.95, 3.48 and 1.335 mm-1 respectively.